lash. In periods of light wind, the sheets might slaken and winching in inevitably leads to trouble. Jury rigged tensioners were often dreamed up to cure the problem, and were only marginally satisfactory. Alternative control traveler approaches to sheet include the threaded-rod mechanism marketed by Dumas (1) ball-chain traveler varieties available from AmPro (2) and Johnson Engineering (3). By far the largest proportion of all sheeting systems in use today utilize the “swing-arm” technique pioneered by Vortex Model Engineering (4). This method can be configured to be a single ended arm, as in the standard Santa Barbara installation (Figure 1), or as a double ended arm found in _most East Coast 12-meter boats Ks | | 3 Hifi| fi] or a ee ] oF | Ne | 3RD CHANNEL VOLTAGE SELECTION oe | UD sell Pe 4 | efeail FAST OUT — SLOW IN RADIO CONTROL VARIATIONS OF 6 WIRE CONNECTIONS (Figure three BY ROD CARR c 2). The swing-arm provides important benefits: First, it is completely free of a tendency to foul the sheets should they be slack while the winch is being operated; Second, a proper The practice of R/C sailing requires a vehicle and R/C gear as do other phases of the sport. Rather than an engine yacht for power, requires a model sailing a means of trimming the sails in order that the vessel be able to sail at a chosen angle to the wind that propels it. This means of trimming is variously known as a “winch,” a “sail servo,” an “SCU”’ (sail control unit) or a “sheeting servo.’ No matter what it is called, the mechanism needs to fit the following general criteria: b) Provide 50 inch pounds of torque. c) Use 6 to 9 volt battery power. problem skippers of sail approach sheeting by the direct application of prototype drum winch practice. Commercially available geared motors are used to provide the strength needed for and The jib sheet. reeling in main usual between jib and main is maintained from close-hauled, through reaching to running free. The sails work together without need for separate adjustment difficult because the geometrical which may be of distance; Third, relationships in the swing-arm technique provides for less sheet travel per degree of winch rotation when approaching the close hauled position. This allows for fine adjustment in this important part of the sailing envelope. Installation and adjustment of such a unit in your boat is not difficult. a) Weight — | lb. Many relationship problem which arises is the need for maintaining tension on the sheet in order that it feed on to the drumwithout back- _ However, spend you some must time be on prepared studying to your boat underway and making the small changes which which any will result in a boat operates at top efficiency on point of sailing. Some skippers carry an extra winch in order to be able to trim the jib relative to the main as a separate function. This is not necessary until you have reached the point in your experience where you don’t make tactical, or helm, mistakes. manufacturer Believe me, would two hard rudder move- fall and into appears the ‘as The third it ready-to-run at . $65.00 price area (Figure 2). ments will cost you a boat length in if winch was a smaller Racing Rules than you are adding a 36/600 class activity which has flour- never admitting to yourself that it is you and not the boat who is getting beaten! Atsthe close of 1972 the Drone” supply suddenly dried up. No longer can a skipper easily purchase one of these units for conversion purposes. As the word of this disaster circulated among American model yachtsmen we realized that the future of the sport ‘rested on a replacement for the “Drone,” though we all knew that the $4.00 price tag was not realistic. We also identified a need for an SCU which might be more compact for use in the rapidly growing 36/600 and 50/800 AMYA classes. By mid-Winter prototype units three firms had under construction. As of this writing one of the units, Hercules, is now commercially available (5) while a second, the Jansson Sail Servo, has reached the prototype evaluation stage (6), and a third is still in the initial breadboard configuration (7). : Each of the three new SCU’s pointed itself toward filling a specific along this SCU is at the present time is not known to me. , / | | ! $25.00) to ready-to-run for $35.00. The Jansson oriented toward Sail Servo is reduced more physical dimensions and weight making it more compatible with tight fitting 50/800 hulls, or in other lightweight formula class boats such as 10-Rater and X Class. The JSS sports a 12 oz. weight with dynamic braking on each switch mode. It is, at present, looking for a On} = | = -—O fg : | = o| =}+—o9 —_—_J =e ! | SWITCHER CONVENTIONAL 3 WIRE CONNECTION Or ° : {fiat} ae | SWITCHER 5 WIRE CONNECTION DRONE SCU WIRING Listed at the end of this article are the firms involved in supplying SCU’s to the model yachting fraternity. For detailed. information on a_ specific turer, with prices from bare-gear motor for $19.95, (through assembly kit at the manufac- Dick Jansson (6) was kind enough to offer his wiring schematics to me for inclusion -here. The 6 wire system offers dynamic braking at each switch function, while the 5 wire system only dynamically brakes with operation of the R/C servo switch. Dick also men- tioned that he Drones into single is still re-working function SCU’s which weigh only 8.1 oz. Contact him for prices and particulars (Figure 3). Remember to renew your membership in the American Model Yachting Association by sending your $3.65 annual dues to AMYA secretary, C.H. Black, 4761 Niagra Avenue, San Diego, California 92107. o Any questions, suggestions, photos, or other communication will be grate- —_——| — | — a fully accepted by this writer and may be sent to me direct: Rod Carr, 2713 5 a Blaine [Onn Drive, Chevy Chase, Maryland 20015. 1) Dumas LIST OF SOURCES Products, Inc., 790 Avenue, Tucson, Arizona 85716. SWITCHER JANSSON SAIL SERVO 6 WIRE CONNECTIONS Johnson 4) St., Paris, Illinois 61944. Vortex Model Engineering, Engineering, 420 West 210 Court East Ortega Street, Santa Barbara, California 93101. 5) Carr’s Boatyard, Inc., 2713 Blaine Drive, 6) Chevy Chase, Maryland 20015… Dick Jansson R/C Corp., 6 Pine Street, 7) Sr was developed as a simple, inexpensive weight and power of the Hercules was based on the needs of these vessels 3) Wellesley Hills, Mass. 02181. item, write directly to numerous one-design skippers in the S/B, EC/12 and WC/12 classes. The the ished in Southern California. How far need in the sailing classes. Hercules unit which would be suitable for the toward TM~ continually fiddling with the jib, and kd i? Coctval biteSel ey third control function to your boat, Jae, 17 78 proposal more R/C Mode! Sail Yachts, Box 3134, Bur- [| bank, California 91504. any AMYA racing class. You are better off learning careful steering and the pointed 2) S. Park Black’s Boat Accessories, 4993 Niagra Ave., San Diego, California 92107.





