Mainsail onleft, jib on right, 0.5 oz. mylar. First attempt at making sails. All photos on this and next page by Larry Robinson. A C RICTES By ROD CARR K very time I turn around [ am amazed at the collection of technically oriented individuals who keep cropping up here in the Pacific Northwest, making positive contributions to the science and art of model sailboatracing. Theregion has a healthy share of the high tech industry what with Boeing, Microsoft, Microrim, Flow-Mole, and many others. The result is a collection of people with technical backgrounds, plenty of education, and the spare time to pursue hobbies in depth. When that is coupled with the sailing activity we have on the waters of Puget Sound, itis no won—_—_—— t — —~-— der that so much original thinking andexperimentation spills overinto therapidly growing model yachting arena. One such individual I have become acquainted with is Dr. Larry Robinson, of Seattle. A sailor of fullsized boats by avocation, Larry took up model yachting as an adjunct sinceit allowed him the opportunity to experiment with sail and hull design ata fraction ofthe cost of doing it full scale. I first met him at the lake, and learned ofhis hull making experiments. He was kind enough to document them for us, and they will make an excellent article in a future USBSM. Hesticks to 24-inch LOA sloops, as they may be placed fully rigged in his car and taken to any patch of water ready to sail in any winds. On the relatively small sails, Larry has had to address the sticky issue of precision sailmaking. He approached it with the quantitative accuracy of an engineer and has written down his approach for us. In the following article, Larry’s original words and mine have gotten mixed together. Give him full credit for the concepts and for the framework… the bones, so to speak. Hold me responsible for the fat and plastic surgery that was done to fill in hills and hollows. What results is probably the most specific description of model yacht sailmaking technology published yet. We acknowledge the contributions by such luminaries as Bud Salika and othersin the pages ofthe modeling press and the AMYA quarterly newsletter. But I think you ll agree. . .if youcan hew to the line that Larry has drawn, you and anyone can make beautiful sails that will perform well, and are amenable to either duplication or further analysis as is required. As an aid to keeping who is doing the talking straight, Larry’s description is shown in regular type, with Rod’s comments in italics. We will focus on jibs, as they are most prone to deformation, and if gotten under control, will producethemost improvement for the effort. In the average boat that I see, if the main- sails are 80-85% efficient, thejibs are nomorethan 60%. Jibs are harder to ———— ¢ | 5o 50 i End View Side View az. FIGURE 3 ! Radius ; x Straight (Exaggerated) , Table Edge FIGURE 4 Showing splicing tape reinforcement on mainsail, also black bands and numbering system shown. U.S. BOAT & SHIP MODELER Hand in foreground indicates small size of test yacht. An 18 mph wind was blowing on sails as this photo was taken. set, trim, and control. Over to Larry Robinson. SAILMAKING 1990SAILS BY THE NUMBERS Noting that the principle change in large boat sail design in the last 10 years, in my opinion, has been the alignment of sail panels along the lines of maximum stress, I have wondered how to duplicatethis with model sails. I felt that the UlmerKolius “Tape Drive” concept would be easier to adapt. Several different kinds of tape were tried, but as they were of materials different than the sail cloth, wrinkles appeared with age and with temperature changes. Most recently I have used 1/2 oz. mylar composite (0.004-inch mylar FIGURE 1. Splicing tape reinforcement on five-panel jib. + random fiber backing) with 1/8 and 1/4-inch mylar tape (audio splicing tape from Radio Shack). This tape, only 0.001-inch thick, is strong enough to add substantial strength to the sail, but not so in- flexible that it produces hard spots. This tape must beappliedin straight lines … it can’t be curved at right angles to its direction of run, as one sees in the tape drive advertisements, to follow the lines of stressin the sail (See Figure 1). One-can approximate the stress directions and the results are shown in the accompanying photos. Unfortunately they don’tshow the fullsail. . .they were taken to document sail shape. These new sails are great. They are sensitive to the lightest air and yet still have good shape at 20 mph, documented. There is significantly less stretch. Thus much less change in sail trim is required for changes in wind speed. An unexpected benefitin both light and moderate winds, there is an auditory as well as a SPRING 1990 visual clue to luffing. You can hear mylar sails luffing. If a competition skipper waits to hear the sails shake, he will bein the top of C fleet at best, with an open invitation for D fleet in his mailbox! If the light material shows the “bubble” easier and earlier than other materials, that may beauseful advantage. Experiments by Larry showed thatsucha of reinfor system cement would effectively maintain andprotect whatever sail shape was built into the sail by its maker. It was then obvious that better sails could now be devised, and one could count on them to hold their shape and perform. Larry embarked on ex- periments to produce model yacht sails by a technique that allowed one to reproduce any sail almost 63 derstanding. As a reference, I started with: THE BLOCK, AMYA QNL Reprint, ““The Block Heard Round The World.” The blockisameans by which the amount of seam taper can be controlled in each seam, thereby building up a sail shape which is curved in three dimensions. Larry takes this approach a good deal farther and introduces substantial improvement in precision and accuracy so that later analysis of the shape of the sail can be related to how it was originally constructed, seam by seam. The shape of the block was modi- | fied to allow: 1) Numerical representation of the shape. 2) Exact reproduction of panel broadseam shapes. 3) Ability to change fullness of sail easily by a known amount. 4) Ability to control position of Don Kirkland’s 12/US 16 East Coast 12-meter shows lovely sheerline original to the class and maximum draft location in each now regained in the International EC/12 class. seam and in conjunction with the luff curve. Straight-grain 2×3 stock is used to Blocks were made with a fixed make the blocks. All surfaces are taper angle (five degrees below the first jointed for mutual perpenll overa Finished boat—Hull is 26-7/8 inches horizontal), a curved section of condicularity. A table saw was set ata length, beam 5-1/2 inches, draft 14 inches, disstant radius, and a tangential five-degree tilt and the top of the placement 3.01 pounds, ballast ratio is 0.323. Robinson photo. straight section to produce a flat block was ripped. Set a knife blade exit off the leech of the sail. The marking gaugetotracethecenter of exactly if it was found to perform doubled five-degree angle allows atthe block, mark the center and carewell. He typically deals with jibs fully plane off any saw marks. taching double-stick tape to one having an 8-inch or 9-inch foot, and The radii built into the blocks are panel without it adhering to the 30 to 36-inch leeches. obviously related to the camber reI decided to write the following to other panel until everything is lined quired in the sail. Having picked a up just right (See Figs. 2 and 3). document my current level of untarget camber, say 1/10, then the r chord length (perpendicular to the mast) and the camber depth can be Heavy Air used to calculate the radius required for the block. Probably a simple table would suffice, with camber Increase in and sail chord dimension as entry a f entry a Ay. lS Light Air —— FIGURE 6. Entry angle change under jib stay sag. Relative size of Larry Robinson’s hull shown with its designer, who is checking rudder leading edge radius (1/32 inch). 64 points forradius. Table 1istheresult of much head scratching. Simply select the camber and the sailchord, read theradius required of the block. Using trammel points witha knife edge marking point, layout desired radius, such that the curve traced comes out tangent to the planed surface several inches from the end of the block. Use carein this layout. Now bandsaw the arcroughly to shape (See Fig. 4). Without resetting the marking gauge, remark the centerline of the newly exposed curving face of the block. Using a sanding disk on a table saw set to five degrees, sand block to the knife line. Don’t sand onto the straight part at all. Accuracy is important. Round the outside edges of the block to avoid snagging or creasing of the sail material. Younow haveablock with U.S. BOAT & SHIP MODELER Tracey Carr models Radio Glove, $29.95 from Radio Glove, 1077 S. 930 W., Payson, UT 84651. Snug and warm for frostbitten sailors. Rod Carr photo. a constant radius, and a straight section that can be used to manipu- late the position of maximum draft in thesail. I’vemadeaseries of such blocks with radii of 16, 24, 35,48 and 60inches. Each blockis labeled with the radius and anS for straight,i.e., 16S, 24S, etc. 2 MAKING THE SAIL The sailis drawn full size on ‘ butcher paper taped to the table. Four equal width panels are drawn with seams perpendicular to the leach. (Threeseams). Depending on _thesize ofthesail, more panelsmay be required. The top panel is one Some new BB radial swivel jib fittings by Bill Whitten. How about some details, Bill? A 10R at left, 36/600 at right. Photo by Bill Whitten, Birmingham, Alabama. half the vertical dimension of the rest of the panels in an attempt to maintain good shape as close to the head of the sail as possible. A “foot shelf’ seam is added just above the clew patch, angled towards the tack to produce a slight shelf. This gives some end plate effect as well as gaining some unmeasured sail area. _ Asmaller drawing of the sail is made, on an 8-1/2 x 11 sheet to be ~ keptin a notebook. On this sheet go all measurements, special tech- niques, ideas for next sail and re- sults of sail photos, apparent speed observed. This will allow you to recreate the sail precisely if it turns out to be a real winner. Be sure to includethe block used foreach seam, and the amount of straight block used in the taping up of the seam. SAIL CONSTRUCTION The panels are cut oversize and broadseamed over the appropriate block. For example, one jib I made had an86 em (33.8-inch)luffandan _ 18 cm (7.09-inch) foot. The blocks used from top to bottom seam were, 24S, 35S, 60S, 60S, 24S. The seam edges are cut straight, thatis, the panels used to make up thesail arecutfrom theboltas seine with the sides parallel. Broadseaming (tapering the overlapping seam for shape) is accomplished by developing the taper (of the seam) by the action of the curvature of the block. Sailsin the photos weremade from 0.5 oz Mylar. One panel is taped to the block FIGURE 7. Luff Curve shown against a straight jibstay reference line. TABLE 1 = “ BLOCK RADIUS ar FOR CAMBER CAMBER AND SAIL CHORD $e SAIL | SELECTED : CHORD CINCHES) 10 12 14 16 18 28 ED 24 16% 7.5 g 1@.5 12 13.5 15 i6.5 18 13% LLGint 18.5 Las 14 15.75 t7<5 19.25 Pal 10% 214625 134.5 SatSacs 18 20.25 22.5 24.75 Dee 8% 13.75 16.5 19.25 22 24.75 27.5 38.25 33 6% 16.25 19.5 22.75 26 29.25 32.5 35.75 39 SPRING 1990 65 _, The 13th edition of the RADIO CONTROL BUYERS GUIDE is _ available at your hobby shop or oner direct from Kalmbach! =| Now you can own the source book of radio control modeling information — — the RADIO CONTROL BUYERS GUIDE! In more than 300 pages, and thou- _ sands of product listings, this all-new 13th edition of the RADIO CONTROL BUYERS GUIDE provides the up-to-date information every radio control en- husiast needs — whetheryou’re a beginner or a NATS.champion. There’s no other r RIC book source like it! #12086 _ @ Aircraft e Cars e Boats e Radios e Engines _@ Hardware e Books @ Videos @ Finishing materials _ @ Accessories @ R/C dealers @ Plus much more! $12.95 ORDER TODAY! Kalmbach Publishing Co., P.O. Box 1612, Waukesha, WI 53187 YES! Please send me (_] My check is enclosed. copies of the RADIO CONTROL BUYERS GUIDE! Price per copy is $12.95/# 12086. [] Charge my credit card Chargeto: Name Card # Street Exp. date City, State, Zip Signature L) Visa (] Mastercard Include for postage and handling: U. S. $1.50; Canadian and foreign add 15% (minimum $3.00). Make payment in U. S. funds. Wisconsin residents add 5% sales tax. break, (1.e., luff evenly along its entirelengthatonetime)andthemain is set to luff first in its upper reaches during a gust, the boat willround up slightly as wind velocity increases, then sail straight without further rounding, and eventually fall off slightly when the gust passes, all without touching the helm. The current solution is to make the luff curve of the jib match the sag in the headstay, with some special considerations that will be discussed later. (Somewhere, somebody has aformula that will predict the forestay sag, based on sail area/loading, initial stay tension, and soon. Hello out there, structural engineers.) A straight luff won’t work, luff hollow is required. This is much easier if the seam is straight from jibstay line forward ... the part that will be folded back to form a pocket (tabling) for the stay. FINISHING THE LUFF All panel seams are finished, on larger sails by sewing azigzag stitch which straddles over theseam tape. On very small sails, or on very light air sails, the seam tape may be enough by itself. The sail is placed over the original butcher paper pattern with the head and tack refer- 68 ence marks placed over the luff line on the pattern and taped to the pattern to maintain a minimal tension along the luff. Extra material more than 3/4-inch outside ofthe luffline is trimmed away toeliminateitasa source of interference in theremaining steps. The clew is then lifted off the pattern, so that all wrinkles disappear andtheentiresailassumesa fair three-dimensional shape. While holding the clew elevated, the sail panel seams aremarked wherethey cross the luff line on the pattern with a very fine marker (0.05mm drafting pen). These marks become the luff line on the sail that will allow proper sail shape if set on a straight jib stay in light air. MODIFYING THE LUFF CURVE Notethatajib withastraight luff, generated as above, seton astraight jibstay, will set well in light air, but as wind speed increases, the load in the sail will cause the stay to sag, pushing extra cloth into the middle of the sail along the luff. Under this influence the sail will be able to sail as high relative to the wind, and its ability to heel the boat willincrease. Increasing jibstay tension will postpone the sag and reduce its 0106 severity somewhat, butsomejibstay sag will always have to be dealt with. Thesolution is the“S” shaped luff curve for all but the lightest air. The approach is to remove cloth which matches the jib stay sag. This will reflatten the sail, and reduce its tendency to luff at the head. Three possible luff curves could be cut as shown in Figure 7. CUTTING THE LUFF CURVE Place the full-sized paper sail pattern such that lufflineis about 1-1/2 inches back from the edge of the table to allow clamping ofa straightedge cutting guide with spring clamps. Apply head and tack reinforcements to underside of sail such that when the luff tabling is turned over the patch will be outermost. Use “sticky back,’ a self-adhesive dacron availablein several weights. It is strong, flexible, and sews well. Tape the sail to the paper pattern atthe head and tack, with head and tack reference marks over the pattern reference luff line. Tape the sail down along the luff edge, adjusting the seam reference marks in relation to the pattern reference luff line to produce the de- U.S. BOAT & SHIP MODELER sired curve in the luff. Measure and record the distances at each panel seam to the nearest 1/2 mm. For example: in arecent medium air jib HAYES WHIP ANTENNA i (which had a180mm foot), thereference marks were pulled forward of the pattern’s luff line 3mm (27% of chord) at the top seam, 4mm (18% of chord) atthesecond seam, 4mm (8% of chord) atthethird seam, 2mm (3% of chord) at the fourth seam and Omm atthe fifth seam. This sail was built to provide a better match be- above, place push pins 3/8-inch aft of luff line at head and tack. Place straight edgeagainst pins and mark sail with 0.5mm marker. This line SPRING 1990 marks the place aft limit of the “folded over” tabling that will enclose the jibstay. Place push pins 1/4-inch aft of luff line at head and tack and place straight edge against them. Clamp straight edge and apply 1/8-inch seam tape aft of the straight edge. Place push pins at head and tack, 3/8-inch forward of luff line. Clamp straight edge and use small square or end of aruler to mark perpendiculars with .05mm marker at 1-1/2 inch intervals to insure accurate folding of the luff. Cut the entire luff against the straight edge as placed in the preceding step. An OLFA rotary cutter used for sewing works great, or a super sharp razor blade. Remove backing from the seam tape and carefully fold the seam, aligning perpendicular marks and using the 1/2, 1/4, 3/4, etc. method. FINISHING THE SAIL Trim leach and foot to size. Apply 1/4-inch and 1/8-inch mylar splicing tape in various patterns which will increase the wind range of the 1/2-0z mylar dramatically by reducing the amount of sail deformation caused by wind pressure. As a start copy the Ulmer-Kolius “Tape Fax 718-981-1178 718-981-7400 Staten Island, New York 10303 14325 Commerce Wy. Garden Grove, CA 92643 2178 Forest Avenue HAYES PRODUCTS ca minimized by use of stay wire and as little dacron cord for operation of a bowsie as possible. One might consider an easily adjustable turnbuckle with some kind of index marks to allow a reproducible setting. MAKING THE LUFF POCKET (TABLING) With sail taped in position as spring steel diameter for resistance. at your dealer. M backstay/forestay system should havea built in capability for stretching, or at least it should be Stainless whip only 1/32 minimum wind Available local R/C cars and tors, vertical mounts and included. winner! Well, it depended on the wind, for heavier air was required to make it and its relatively flat shape do the job. CHOOSING A LUFF CURVE Light air jibs and mains ... straight luff, sail reference marks directly over pattern reference luff line. Allpurposemains. . .forstraight masts, add a few mm of cloth to lower half of sail, make top half as above. This approach avoids 1) diagonal wrinkles, and 2) excessive forward movement of draft and increaseinentry angle at head of sail. Medium and heavy air jibs: Pull top halfofthesail forward ofthe luff line to match the estimated headstay sag. Then push the lower half aft as much as possible such that a straight edge placed over the luff line causes only theslightest wrinkling of the sail material. Try to tension the sail to remove all wrinkles. Luff curve matches C in Figure 7. Note that one needs to develop a means of establishing a reproducible jibstay tension. No part of the — antenna for boats. Connec and horizontal safety ball all Rossi engines have powered world champions for 17 consecutive years. For information on the complete line of Rossi engines and spare parts, call or write: curve was much like Curve A in Figure 7. Was the sail a success? antenna replaces any 18 or 36-inch [receiver makes you a bit and not allowing the draft to creep forward, increasing the entry angle and likelihood of luffing. The Vertical whip Rossi...Gives you the competitive edge. tween the leading edge of the sail and the sag in the jib stay expected in higher winds. More material was removed at the head and upper seams, thereby flattening the sail a f el ie PRATHER RECORD BREAKING BOATS LAP CAT I Tunnel WHY CHOOS E A PRATHER BOAT? AWESOME COMPETITION CLASS PERFORMANCE! Our contest proven hulls hold more N.A.M.B.A. National Championships and World Speed Records than any other manufacturer. These competition class hulls will deliver awesome performance even if you just want to have a fun day at the lake. Epox “lass construction provides mally times the strength of polyester resin as well as reduce S rinkage for an accurate true hu * Economical * Stable * Step-by-Step Photo Instructions af PRATHER PRODUCTS, INC. 1660 gavenna ave. witmineton, ca 90744-1398 (213) 835-4764 SEND $2.00 FOR COMPLETE CATALOG Drive” pattern. All seams and taped areas are now rolled with the barrel roller. Three black bands are now applied parallel with the horizon (waterline plane) at 1/3,2/3and5/6 height of the sail. Use dry transfers lines, or on larger sails by painting the lines. I now sew the sheets, halyards and downhauls to the corners of the sails, preferring that to grommets. On larger racing sails, the grommets are fine. Given that they allow for easy replacement of outhauls and so forth at lakeside without special equipment. Dry transfers are used to number the sail. In doing my research, I have a system such as seen on the full-sized 12-meter boats, using a largenumeralandasmallnumeral: 14. This means the fourth #1 or fullsized sail. Thenumber is placed just below the lowest black band such thatit can beseenin photos taken of the sail on the spar and full of wind. THE SAIL IS FINISHED... TEST SAIL Documentation is important and photographs ofthesailsonthespars and held in a wind of measured strength are invaluable. Using dial calipers and a jewelers loupe, data can betaken from the photographs with which to calculate camber and location of maximum draft. This data should be recorded on the drawing done of the sail. Note problems and plan corrections for the next sail; e.g., ““middle seam too tight, switch from a 34-inch radius block to a 48-inch radius block. Eventually you'll home in ona proper shape and will be able to repeat it in subsequent sails. Now back to Rod Carr. I think you will agree that Larry has given usa masterful description of his approach and methodology. Here for the first time, are the nittygritty details necessary to make a PERFORMANCE REDEFINED SHOCK WAVE fi SPARTAN GRAND PRIX 45 SPORT CLASSI & Il = p> Joined Deck & One Piece Cowl p> Engine Bearers Drilled & Positioned For 4” Mount > Kit includes Decals Shown p> Uses Hardware Set #69 Manufacturer of Precision 4 Quality Cable Nuts & Tuned Pipes. SEW MUCH ric Boats | 6003 Daven Oaks Dr. Dallas, TX 75248 214-380-9274 70 Send *1.00 For Catalog U.S. NAMBA NATIONAL WINNER sail, judge its shape and effectiveness, and then make measured changes to the next sail built, to improve performance. Thanks, Larry, we certainly appreciate your insight and your willingness to share it with us. In order to rescue the United States bid for the East Coast 12 Meter World Championship scheduled for 1991, concerned skippers have set about to establish the International East Coast 12-Meter Class within AMYA. Thisis aresult of the confused results of the recent AMYA ballot. All existing AMYA EC/12 boats are eligible to be registered for $2.00in thenew class. Send registrations to: Ron Banner, 115 17th St. SW, Puyallup, Washington 98371. Ron states that the [LYRUModel Yacht Racing Division rules will be the class standard, and each skipper will need toremit $1.00 each year to AMYA to pay the IYRUMYRD levy on International Class yachts. Now that the paperwork is out of the way, plan to come to Seattle in 1991 and sail in the World Championships. It is going to bea super event with skippers from many countries taking part. Remember to renew your dues to your local club and to the American Model Yachting Association, 1884 Campus Court, Rochester Hills, Michigan 48309. Send me pictures of your most recent project. There are alotoffolks out there who wonder what you’ve been doing in your workshop. Questions and comments to: Rod Carr, 3011 – 177th Ave. NE, Redmond, Washington 98052. U.S. BOAT & SHIP MODELER PRATHER RECORD BREAKING BOATS AWESOME COMPETITION CLASS PERFORMANCE! Our contest proven hulls hold more N.A.M.B.A. National Championships and World Speed Records than any other manufacturer. These competition class hulls will deliver awesome performance even if you just want to have a fun day at the lake. Epox glass construction provides many times the strength of polyester resin as well as reduce S rinkage for an accurate true hu . * Economical * Stable * Step-by-Step Photo Instructions af PRATHER PRODUCTS, INC. 160 gavenna ave. wicmineton, ca 90744-1398 (213) 835-4764 SEND $2.00 FOR COMPLETE CATALOG Drive” pattern. All seams and taped areas are now rolled with the barrel roller. Three black bands are now applied parallel with the horizon (waterline plane) at 1/3,2/3and5/6 height of the sail. Use dry transfers lines, or on larger sails by painting the lines. I now sew the sheets, halyards and downhauls to the corners of the sails, preferring that to grommets. On larger racing sails, the grommets are fine. Given that they allow for easy replacement of outhauls and so forthat lakeside without special equipment. Dry transfers are used to number the sail. In doing my research, I have a system such as seen on the full-sized 12-meter boats, using a largenumeralandasmallnumeral: 14. This means the fourth #1 or fullsized sail. Thenumberis placed just below the lowest black band such thatit can beseenin photos taken of the sail on the spar and full of wind. THE SAIL IS FINISHED… TEST SAIL Documentation is important and photographs ofthesailsonthespars and held in a wind of measured strength are invaluable. Using dial calipers and a jewelers loupe, data can be taken from the photographs with which to calculate camber and location of maximum draft. This data should be recorded on the drawing done of the sail. Note problems and plan corrections for the next sail; e.g., ““middle seam too tight, switch from a 34-inch radius block to a 48-inch radius block. Eventually you’ll homeinona proper shape and will be able to repeat it in subsequent sails. Now back to Rod Carr. I think you will agree that Larry has given us amasterful description of his approach and methodology. Here for the first time, are the nittygritty details necessary to make a PERFORMANCE REDEFINED Championships. It is going to bea super event with skippers from SHOCK WAVE II many countries taking part. SPARTAN GRAND PRIX 45 SPORT CLASS| & Il p> Joined Deck & One Piece Cowl p> Engine Bearers Drilled & Positioned For 4” Mount > Kit includes Decals Shown > Uses Hardware Set #69 Manufacturer of Precision Quality Cable Nuts & Tuned Pipes. a SME Wie MW C”S ric Boars 6003 Daven Oaks Dr. Dallas, TX 75248 214-380-9274 70 sail, judge its shape and effectiveness, and then make measured changes to the next sail built, to improve performance. Thanks, Larry, we certainly appreciate your insight and your willingness to share it with us. In order to rescue the United States bid for the East Coast 12 Meter World Championship scheduled for 1991, concerned skippers have set about to establish the International East Coast 12-Meter Class within AMYA. Thisis aresult of the confused results of the recent AMYA ballot. All existing AMYA EC/12 boats are eligible to be registered for $2.00in the new class. Send registrations to: Ron Banner, 115 17th St. SW, Puyallup, Washington 98371. Ron states that the LYRUModel Yacht Racing Division rules will be the class standard, and each skipper willneedtoremit $1.00 each year to AMYA to pay the IYRUMYRD levy on International Class yachts. Now that the paperwork is out of the way, plan to come to Seattle in 1991 and sail in the World Send £1.00 For Catalog U.S. NAMBA NATIONAL WINNER Remember to renew your dues to your local club and to the American Model Yachting Association, 1884 Campus Court, Rochester Hills, Michigan 48309. Send me pictures of your most recent project. There are alotoffolks out there who wonder what you’ve been doing in your workshop. Questions and comments to: Rod Carr, 3011 – 177th Ave. NE, Redmond, Washington 98052. U.S. BOAT & SHIP MODELER





