Radio Control Boat Modeler: June 1997

  • Title. Author. Summary
o N Oo Bmemo RADIO CONTROL yc In-depth— Futaba 3PJ SUPER RADIO : Racing Action CANADIAN NAMBA NATS a1 LAS VEGAS ——1 * TESTED THIS MONT BANDIT BOATS Pisto GAS GRAND PRIX @2oZ-TOTT9 ay KYOSHO i Thage, Vip MRP Miss Bud Hydro | GY TWO 96 d3S IT au Avs LIND J0u dviINng ¢ 4 10008 703 6TTOS BT BeMS ea OS age.com [ihe ay | Hopping Up the Thunder ‘Tiger | Victoria by ROD CARR N THE JULY ’96 issue, we detailed the construction of the Thunder Tiger* Victoria sloop, following the kit’s directions. Having successfully launched and sailed the boat, the next project was to identify areas where performance could be improved. Most performance improvements were related to replacing the original flat, woven sails with new paneled sails made out of TriSpi 25 Mylar. The material weighs 0.6 ounce per sailmaker’s yard, and it is lighter than the original material. Its use reduces weight above the water line and helps the boat to heel less under wind pressure. Presenting more sail area to the wind gives the boat greater speed potential. Because the modifications will allow the rig to generate more power, additional strength and control must be present in the standing and running rigging. I ‘ The (Queen (sets lal a Ce /| se recommend that you drill holes through the mast fittings and press brass rod of the appropriate size (7/64 inch) through the holes to lock the fittings in place. The sails are each made in three panels and have tapered seams that produce sail camber. I attached the mainsail to the mast using the included kit rings; next, I tied the head of the mainsail to the masthead crane; then, I rigged a downhaul from the mainsail tack (lower front corner) down to the Glued in chainplates ! aD aN lower mast fitting where the boom vang is LO Fill attached. I fitted a three-hole bowsie to add ten- sion to the mainsail luff. Remember to remove the tension (slack) when you’ve finished sailing New hole drilled in deck Bia eel Deck Figure 1. Chainplate modification to the lead shrouds (left). 56 RADIO CONTROL BOAT MODELER because a continuous pull on the luff will stretch the sail. The new jib has a hem (sailmakers call it a tabling) in its luff through which the jibstay is run. I used some plastic-covered, braided, stainless-steel leader wire called SteelonTM, which you can buy in a fishing-tackle store. +m — Bow Cockpit area Twenty-pound test is sufficient for a boat of this size, but remember to get a pack of little swaging sleeves while you’re there. The jib tack is tied to the jib club, and a bowsied halyard is installed at the head to allow the jib luff to be tensioned. An efficient sail is designed to have some twist as it goes up the mast. To accomplish this, let the clew (aft lower corner) of the sail lift slightly. For the mainsail, this lift is controlled by how tightly the vang is set. For the mainsail, a good starting point is a total twist of 15 degrees between the foot of the sail and the head. The leach of the jib does not follow the curve of the mainsail’s leach because the jib does not have enough twist to match the mainsail. The tension in the jib leach is the result of the upward pull on the jibstay (which comes from the backstay tension) and the pivoting of the jib club at its swivel. Left unopposed, the leach of the jib is very hard and tight. There is no vang on the jib club, so it’s necessary to find another way to balance the downward pull of the jib Y-inch plywood backing Guide—plastic or brass Main sheet New hole Figure 2. Cross-section of new mainsheet exit guide. The ‘/s-inch plywood thwart is epoxied underneath the deck between the two winch drums and in the new hole that leads the mainsheet from the cockpit. ping lift to counter the downward The included hatch cover was quite pull of the jib club, and the jib leach thick and heavy, so I replaced it with is free to assume a nice curve that can a very lightweight rectangular piece of be made to match the mainsail. When 0.015-inch-thick white styrene sheet. I the curves match and the opening made a semicircular cutout to clear between the jib and main is proper, the new mainsheet exit guide; this the two sails will work together. retains the cover—without tape or any To neaten the deck layout and to allow the mainsail to be set with some other complications—while the boat is sailing. precision, I replaced the bowsies and split-ring arrangement with a plasticsheet exit guide. In this new position, the mainsail may attempt to wrap itself around the winch drums. Either remove the drums, or if you’d like to keep them for their scale appearance, use some springy wire to make a cou- ple of guards (Figure 2). These will lead the sheet up and over the drums without fouling. club at the clew. A topping lift works well for this purpose. The topping lift should not be a “stretchy” line (use Spectra kite string of about 30- to 50pound test); it is tied to the jibstay attachment point on the mast, then it comes down through a small eye on the back of the jib club. (I drilled a small hole and bedded a small cotter pin in epoxy.) To allow its length to be adjusted, install a four-hole bowsie. The bowsie settles about halfway between the jib Above: the area between the winch drums just forward of the cockpit. I epox- ied ‘/s-inch plywood thwart underneath the deck between the two winch drums and the new hole that leads the mainsheet from the cockpit. Right: this shot of clew and the black, lower jib-draft the mainsail provides a good overall view stripe. You can now adjust the top- of the shape that the new sail provides. JUNE 1997 57 THUNDER TIGER VICTORIA The original construction shows the side stays that hold the mast up as being attached to plastic chainplates that are glued to the deck. If I were to build a second Victoria, I would modify this arrangement somewhat for greater strength and to provide better control over the shape of the mast. First, I would epoxy a ¥8×1%4-inch piece of ‘-inch plywood under the chainplate locations on either side of the deck. These would be positioned as shown in Figure 3. Then I would drill a new after-hole ill where the first plas- Oo. tic chainplate Bees =. gene The jib-topping lift detail. This, along with the bowsie, allows the would be mounted. independent adjustment of the jib leach shape. Alternatively, in bead of epoxy to the aft, lower, cen- brass screw eyes I set up the running rigging according to the instructions, with could be turned the exception that I into the plywood. decided to use two This arrangement completely separate strengthens the mounting points sheets for the jib and the mainsail. I replaced for the side stays the provided sheet line in the sail. and improves the lead angles for the lower shrouds with 50-pound-test (which will keep able in kite shops. This kind of line is very slip- When you store the boat, remember to relax all the tensions on the sails and riggings. If the sails remain under pressure between sailing sessions, they will stretch beyond use. place of the plastic chainplates, small, Spectra—a very non- stretchy line that’s avail- the mast straight in its lower section Starboard quarter showing sail when sailing in leaches. You should put a twist pery and helps reduce the friction that the sail heavier air). I in the mainsail for best perfor- winch has to work haven’t had time to mance. For the record, the jib against. Because the needs more twist than is shown. swing arm is rigged as a make this modifica- tion yet, so the photos show it with the original arrangement. I replaced the kit-supplied stay material with 30-pound-test, braided, Dacron fishing line (even 10-pound would be strong enough). It doesn’t stretch and allows you to set up the rigging with some measure of precision. double purchase, I worked a brass grommet into the end of it and spent some time polishing it with Spectra line and fine auto-body polishing compound. I still use the kit-supplied spring fittings for holding the clews of both sails to their respective booms. To provide a better grip on the smooth aluminum, I applied a 1-inch-long terline of the jib club and main boom. Sailing in heavier air may require that the spring fittings be replaced, or at least helped by loops of Dacron line passed through the clew grommets and under the jib club and booms to carry the vertical loads If you make these or any other modifications, let me know how they turn out. New sails can be obtained from any of the established model yacht sailmakers. If you send an SASE, I can provide a list. Send comments and suggestions to Rod Carr, 3011-177th Ave. NE, Redmond, WA 98052; or via email at 102362.1771@compuserve.com. If you would like to know more about R/C yachting activities in the USA, why not take out a one-year membership in the American Model Yachting Association? Check the address under “National Organizations” in this issue. The $25 fee will get you four informationpacked periodicals that focus solely on R/C yachting. Tell Harry that Rod Carr, AMYA no. 002, sent you! “Addresses are listed alphabetically in the Index of manufacturers on page 72. Springy wire—make 2; install crossed at 90°. Figure 3. If you decide to keep the winch drums for their scale looks, install guards made of springy wire to prevent the mainsheet from wrapping itself around the drums. 58 RADIO CONTROL BOAT MODELER Lb