Radio Control Boat Modeler: November 1992

  • Title. Author. Summary
FSHORE RAC FIRST U2S. GAS OF November 1992 ‘ we MONS 2 ae me RADIO CONTROL , ‘More HowO/BTo’s:Y _ “ASTRO 40 CONVERSION | EASY-TO-BUILD FORMULA SAILBOAT, E HULL /%y ~ ‘ y, ‘ fhee 7 THUNDER :STREAK . /TOPCAT CATAMA wARAN ‘RO & ~ PRATHER : ‘3 Build a Formula-Class Yacht Hull by ROD CARR and DR. LARRY ROBINSON HIS IS THE first in a short series of articles that will describe how to build an inexpensive R/C yacht for rough-cutting the hull. hull quickly and allow templates for the final-shaping of the hull. [Editor’s note: see Fred Lehmberg’s “Hull Forms for Scratch-builders” hull testing as you go along. The method works best for canoe hulls, i.e., hulls that You’ll also need drawings of hull cross sections (called stations) that you’ll use to make in the March-April, May and The Robinson 24 is on display while its skipper, Larry Robinson, waits for the Seattle rain to stop. This boat was built using the method explained in this article. The hull bottom profile has been cut out of laminated foam blocks. At this stage, a center line is drawn from the bow to the stern on the deck side of the plug, and along the “keel line.” The deck profile has been cut out and awaits shaping. 38 RADIO CONTROL BOAT MODELER | Foam, fabric and resin construction don’t have deep, thin keels. (Marblehead and 1 meterclass hulls typically have canoe bodies; their stability is provided by fin-and-bulb keels, which are attached to the bottom of the hull.) This method entails making a foam plug, testing it, then sealing it with paraffin and using it as a male plug on which you’ll make a light fabric-and-resin hull. The system described here has been used to make a series of hulls that have an overall length of 24 inches, but you can use it to make hulls of virtually any size, as long as you make the appropriate adjustments to increase strength in larger hulls. You’llneeda full-size set of lines for the hull you intend to build—ines that will allow you to make the side-view and top-view patterns you’ll need’ July “91 issues of Radio Con- trol Boat Modeler for tips on “lofting” your own hull lines.] Laminate 1-inch-thick white foam planks with 3M-77 spray adhesive to produce a block that’s approximately 1 inch longer, wider and deeper than the hull you plan to build. Square the block using a table saw and jointer, or square it with a tri-square and a coarse sanding block. Transfer the side view of the hull to the side of the foam block. Place the sheer line !/s inch below the top of the block and, around the edges (top view), allow 1/16 inch for the thickness of the hull skin that will be added. Cut the block (plug) with a band saw to match the side view, then sand lightly until the curve is approximately what you want. Save the cutoffs (photo 1). Scribe a center line completely around the plug by placing the plug on its side on a smooth, flat surface and using a wooden block of the proper height as a surfacemarking gauge. This line will run from the bow to the stern along the deck side of the plug, and will follow the “keel line” around the rest of the plug. x @ Left: chamfer the chines first. Make sure they’re symmetrical. Don’t lean too hard, Larry! Right: the hull has been sanded to its | shape and is ready for float-testing. Tape the cutoffs back into place, and mark the deck plan on the top of the plug. Cut away the excess foam with a band saw, then sand gently to the deck line (photo 2). To start shaping the plug, chamfer the chines to approxi- mate the hull shape. The chamfers should be flat and crisp, not rounded (yet). Sand until they’re symmetrical on either side of the center line. Check both by measuring and by eyeballing (photo 3). Now, round the chamfers. As you shape the plug, use the templates from your hull drawing to ensure that port and starboard are symmetrical on either side of the center line. You should also “eyeball” the plug from the bow and stern along the respective silhouettes of sequential hull stations. Carefully run your hands along both sides of the plug to feel for irregularities or differences between the sides. Symmetry is vital if the hull is to behave the same on both port and starboard tack when heeled by the sails. Photo 4 shows the roughly shaped hull ready for surface finishing. FLOAT TESTING When the plug resembles the shape of your hull, begin flotation testing. Float the plug in the bathtub or in a waterproof float tank made of 3/4-inch marine-grade plywood. Carefully put a weight that’s equal to the planned displacement of the finished yacht onto the plug (a chunk of lead or a bag of lead shot works well), Hold the weight lightly to prevent the plug from rolling over and capsizing. Move the weight a short, temporary extension block for the stern, glue it on with silicone glue and fair it to the hull. The fabric can be carried out onto the extension to guarantee an accurate hull shape all the way aft. When you’re satisfied with the plug form, fill any holes in its surface with lightweight | spackle. Sand the plug lightly. fore and aft until the plug sits on its intended water line. Note the following: water line length, position of the weight, heel angle at which the deck becomes immersed and any fore and aft trim changes when the plug is allowed to heel. I built my last boat for running in moderate to high winds, and it was designed to go bow-down when heeled. If it’s trimmed to sit level when heeled, the hull will assume some bow-up trim when it’s Coat the foam plug with paraffin. upright. This bow-up trim is opposed by the force of the sails when the hull is running off the wind. Keep these observations in mind if you do any further shaping of the plug. So far, you’ve probably invested three hours in this project, so if you aren’t satisfied, or if you want to try other ideas, make more foam plugs and do so. If you’re eager, make a simple pencil jig to determine the water-line plane shape from the plug. With a little fiddling, you can even determine heeled waterline planes. FINISHING THE PLUG The foam plug will ultimately be covered with a fabric laminate. To avoid distorting the hull lines at the transom, make THICKNESS ? layers 0.018-inch-thick 100-percent polyester 0.050 inch thick | layer 0.018 inch-thick 100-percent polyester+ 1 layer 0.025 inch-thick 50/50 poly/cotton 0.073 inch thick ? layers 0.025 inch-thick 50/50 poly/cotton 0.078 inch thick (Continued on page 40) FORMULA-CLASS HULL (Continued from page 39) fabric that will form the hull. After it has cooled, you can smooth the waxed surface with a variety of tools, including plastic scrapers (old credit cards), modeling planes, or a foam block. If you pierce the wax coating, reapply it in that area and smooth it again. CHOOSING A FABRIC After you’ve finished making the plug, find a suitable fabric for the hull. The key is to use a jersey-knit fabric that will stretch in two directions and conform to compound curves. Suitable materials that are made of 100-percent cotton, poly/cotton (50/50), and 100- percent polyester are avail- able. Striped patterns are easi- est to work with because they show how smoothly the cloth lies on the plug. You may Larry prepares to install the transom. Note the back stay brace that aligns each sheer. want to make some test layups to get a feel for a few fabrics. I’ve found that 100percent cotton producesa stiff, but brittle, lay-up, and 100- percent polyester produces a strong, but very flexible, layup. A two-fabric sandwich works best for me. (See the chart on the preceding page for more detailed information.) When I made the lay-ups, | used polyester resin so that I’d The foam removal begins. You can eave the bow full of foam for reserve buoyancy andstrength, or you can hollow it out, depending on the sail control system you plan to use. Place the plug upside-down on a 3/4-inch-thick plywood piece and trace around it to prepare a “strongback.” Cut the shape out, but make it ‘716 inch to 1/s inch smaller than the plug all around. Affix the plug to the strongback with silicone glue or another adhesive. (Note: always test the glue or spackle on a piece of scrap foam before you smear it onto your carefully shaped plug.) Now paint two coats of melted paraffin over the plug and the sides of the strongback; 40 allow the first coat to cool completely before you apply the second. Be careful when you melt the paraffin; it’s flammable and can be danger- ous. You need only a little, so you could melt enough for one coat in a well-cleaned tin can (photo 5), Make sure that there are no gaps between the hull and the strongback, and fill all pinholes that appear on the plug surface. The plug must be totally covered with paraffin to prevent it from being dissolved by the resin that you’ll use to bed the RADIO CONTROL BOAT MODELER be able to use thickened poly- ester resin and polyester putty later, when it was time to outfit the boat internally. You could also use epoxy resin, which probably wouldn’t attack the foam (and you wouldn’t have to take such care when you coated the plug with paraffin). lused the second lay-up for my hull. The first was too flexible and the third was substantially heavier than I would have liked. My most recent bare hull (24 inches length overall) weighed 260 grams, and the finished boat was ready to sail at 1,500 grams. After you’ve decided on the fabric, if you’ve decided to use more than one layer, drape the first one over the plug with the bias, i.e., the angle that bisects the warp and woof threads, running fore and aft (photo 6). Use a staple gun to attach the fabric to the center of the strongback at the stern. Stretch the fabric firmly beyond the bow and staple it to the strongback. Now staple the fabric down all around the perimeter of the deck, i.e., onto the strongback pulling and stretching it to make it conform to the curves of the hull. There shouldn’t be any wrinkles, Using this kind of lay-up, you can produce a 1-meter- class hull that will be of a competitive weight. If the hull is longer, such as a 50-inch Marblehead, it will be more difficult to keep the weight at areasonable level. More costly hulls made with high-tech methods will be lighter. To minimize the amount of resin required and control weight, apply the second fabric layer with the bias running in the other direction. Cut off the extra fabric; then saturate both layers with polyester laminating resin. Squeegee out any extra resin. Use only enough catalyst to cause the resin to harden after at least a half hour on the plug. There are two reasons for such along working time. First, excess resin will have.time to flow off the plug and this will reduce overall weight. Second, resins that cure quickly generate heat, so use a slowcuring one to avoid this. If you don’t, you might melt the paraffin and the resin will then reach and destroy the plug. After the laminating resin has cured, apply one coat of finishing resin. Start your surface work on the hull no more than four or five hours after the finishing resin has cured, while it’s still easy to work with. To begin, scrape the hull with a properly sharpened cabinet scraper. The scraper will shave off long, thin shav(Continued on page 49) | never dreamed sailing was so simple! i co The simplicityof going sailing with the Tina Sailboat really Surprised me. The only difficult part of owning this wonderful boat is having to wait for some wind. But, if the wind blows, (and the harder the better). ! am off to the lake. | remove the boat from my car, and attach the mast. This takes about one minute because Tina has no troublesome rigging. | turn on the radio and | am off with the wind and across the lake. | can sail all afternoon without recharging any batteries. It’s wonderful! No preparation, no fuel mess, no waiting for motor batteries to recharge, no cooling off of a motor — nothing! The simplicity of owning and running such a superb boat as Tina is a girl’s dream. No fuss! No mess! No problems! My husband gave me’the Tina R/C Sailboat for my birthday. He did a wonderful job building it. He worked a couple of hours each evening and completed it in a week. The boat is big and beautiful! | knew nothing about sailing and have never been interested in sailing. | have an R/C electric speed boat and | love running it except that when something goes wrong | don’t know how to fix it. | can race for 10 minutes, but then | have to bring it in and charge it for 30 minutes. When | crash it or break a prop, not being very mechanical, | usually ask my husband to fix it. (Actually | don’t like working on anything mechanical). Now for the best part of all! You won’t believe how it fee/s to see your Sailboat drifting along, and suddenly a gust of wind fills the sail. You tighten the sail, and Tina is on her side, slicing across the water at a speed you would not believe! I’ve sailed Tina in 25mph winds and wish | could descrite > : you the “snap” of the sailand the wake she leaves as ~ tacks hard and. trim the sail tight! My husband coum stand just watching me, so he built a Tina for himse ~ ace pee ’ — ig 2 ultimate fun is to race two of these magnilficeTM : sailboats. We get them side by side and when they px the wind and keel over simultane ously, we get so tic k’ start laughing. | have. never enjoyed a hobby as mux enjoy saiire If you want to get into something that is sumper exciting, totally hassle-free, please get a Tina Sailboet change your whole concept of fun! This is what = ought to be. JoArmrme HLKK1423 Hobby Lobby/Klaus Krick in Tina RC Sailhoat…………………….9% $138.00 Tina can be sailed with rudder-only contro! but sa 36” long, 11” beam, 62” height overall.Kit contains durable preformed ABS parts, aluminum and brass “no-rigging” mast Tina contain everything you will need (including sx Servo) to complete the boat except for 2-channe! racie List price $199.95 and boom, heavy weighted keel (ballast is included) andreadycut waterproof sail. Illustrated instructions are simple and we better with added sail control servo. Our Accessory ® Order Accessory Packs: HLKK1424 for Heawy 4LKK1425 for Light Wind. (call for price). have added a radio installation instruction based on our own experience with the boat. 5614 Franklin Pike Circle © Brentwood, TN 37027 © (615) 373-1444 Q ONSTRUCTING AND reviewing Robbe’s* TopCat catamaran turned out to be my most exciting project ever. Iwas heavily into the construction phase of this review when changing |» BOAT REPORT % world events rapidly altered 8 my plans. Operation JL & ¢ Desert Storm took me to Saudi Arabia and other interesting This shows the size of the TopCat and how its rudders swing up so that it sits flat for rigging. The individual is Leo Siciliot of Columbus, OH. He’s the Ohio Champion in 1-meter boats. ROBBE Top Ca | CATAMARAN places while the TopCat waited for my return. I love building German mode! boat kits. I can’t really explain what it is about assembling a foreign model. It could be that I admire the sa: Sail 118 OF! 22, the edge. logical way in which manufac- turers such as Robbe assign part numbers to the parts and stages of sub-assemblies. The numbering of the component pieces corresponds to the sequence of assembly; the number before the decimal point indicates the stage of construction, and the number after the decimal point identifies individual components. This method of numbering the parts is straightforwardandsimple. German kits are also well-designed and well- PHOTOS BY BARNEY KEMPTER | ated with | construct- by BARNEY KEMPTER _ing or laying up a sailboat hull. Much of your time engineered. German models might be heavier _ will be spent making a jig to help with the than those we’re used to, but they can withstand _ installation of the pieces that reinforce the inside moderate collisions and mishaps without sufferof the hulls. The jig allows you to position a piece ing too much—f at all. in an area that would otherwise be inaccessible. HULLS The jig instructions are well-written and easily to follow. It’s just a wire that’s soldered into the Compared with many sailboat kits, the two hulls | hollow end of a threaded brass coupler. Use the come almost completely built. There’s no long | jig to pull the hull reinforcements and blind rivet construction procedure like that usually associ- (Continued on page 53) BUILD A YACHT (Continued from page 49) has cured, block-sand the transom flush with the hull. Leave a clean, sharp corner from which the water can leave the hull cleanly with the wake. Carefully hollow out some space along each sheer, scrape for a good bonding and installing the gear are standard proce- Kansas dures, but we’ll pay close attention to keeping this hull’s construction light but strong. article. Mid Continent R/C Competition Specialists. Contact: Terry Dobson, 1915 Glen Oaks Dr., Wichita, KS 67216. (Full program; fuel-boat We’ll cover these in a future racing; APBA member.) L Missouri Dam Busters Model Boat Club. Contact: Dennis Love, 11212 Marty, Overland Park, KS 66210. (APBA member.) surface and then use polyester putty to attach longitudinal timbers called “sheer strakes” (3/16-inch-square white pine stock is preferred). Dig two or three ditches in the remaining foam perpendicular to the flat deck beams. These frames will main- distorting the hull (photo. 9). Removing the foam is more tedious than tricky. Be careful not to damage the inside of the hull. The last of the foam can be easily cleaned out with some coarse steel wool after you’ve removed the large pieces. Scrape the inside of the hull with the round point of an X-Acto blade to remove all remaining paraffin and to prepare for bonding of interior parts. The photo at the top of the article shows the final product, ready to sail. The prototype had nylon sails, but I replaced them with Mylar to improve performance. Mounting the keel, preparing the deck, Central Kentucky Piranhas. Contact: President Larry Atherton, 3525 Dangerfield Rd., Hodgenville, KY 42748; (502) 325-3733. (Monthly club races April-October; fast electric: IMPBA member.) (Continued from page 45, center line and temporarily attach some tain the sh ape of the hull and allow you to remove the rest of the foam without Kentucky CLUB DIRECTORY Watts Wake Scale Model Boat Club. Contact: Kurt Van Dahm, 237 S. Lincoln St.. Westmont, IL 60559; (708) 968-3189. (SSMA; scale electric, steam and sailboats; meets monthly.) Louisiana Acadiana Model Boaters Association, 703 Rena Dr., Lafayette, LA 70503. Contact: Carl Menard (318) 981-5673. (Gas; IMPBA-sanctioned Timberlake Amp Eaters Fast Electric Boat Club, Downers Grove. Contact: Secretary James Thevenot, 11S068 West St., Naperville, IL60565; (708) 369-1558. (Fast electric.) races.) Greater New Orleans Model Sailing Club. Contact: Commodore Tom Tooker, 1 day St., New Orleans, LA 70124; (504) 837-5880. Indiana Indianapolis Admirals, Shelbyville, IN 46176. RR 6, Box 19, Lake Area Racers, Sulphur, LA. Contact: A.K. Newlin (318) 478-3632. Indy Model Boat Club, Indianapolis, IN. Con- North Shore Model Power Boat Associa- tact: Bernard Bathauer (317) 861-3628. tion, 106 Lee St., Madisonville, LA 70447. Contact: Pres. Phillip Hextal (504) 386-8581. Northern Indiana Fast Electric Model Boat Club. Contact: President Jim Hevel, 902 Sylvan Ln., South Bend, IN 46619; (219) 234-7263. Red River Racing Association, Shreveport, LA. Contact: S ry Don Stamper (318) 868b races.) River City Racing Club, P.O. Box 3471 Evansville, IN 47733. (Continued on page 55) Z MODEL SPORT, INC. 170 Township Line Road e Belle Mead, NJ 08502 Tel. (908) 359-2115 62 RADIO CONTROL BOAT MODELER PERISH Ree Ei | i sei NAME. Seals (order no. 9892 order no. ADDRESS Mees Onder 5 EXP, DATE__ fe U Centsi Sado. Baa MASTERCARD [) NUMBER SIGNATURE. ; relénd coupon. PHONE ay VISA [) Video as : Rush me Robbe’s New Complete Boat Video (order no. LENGTH: 32.7 INCHES (25% larger than others) . . For more information on these and many other exciting RC products, as well RY fea te ans