Radio Control Boat Modeller: July – August 1988

  • Title. Author. Summary
[nse MODEL MAGAZINE | : 2 , _ JULY-AUGUST 1988 » REGATTA ROUND-~-U .M.S. VICTORIO Plan Feature -\ TM — Sd | sSCSCULLING DINGHY Full Size Plans 2 Kit Reviews AN ARGUS SPECIALIST PUBLI: ‘ATION RM SEASCAMP bt 8 Squire Kay’s kit is reviewed by Richard Webb had sailed a R36R last season in the club races and enjoyed it very much. | wanted to replace my home built rather heavy boat with a more competitive model, but quite a few of the club members were buying RM’s so | thought | would progress with them and retain my old R36 for the odd race. | reread the back copies of M.B. and R.C.B.M. to see which R.M. has been winning most of the races, and discovered that No Secret, Trapper and Deception seem to be the favourites, but what a price? | decided to have a chat at the Model Engineer Exhibition in January with the experts on the stand. | explained that | wanted a competitive boat at club level but did not want to pay for expensive exotic materials. It was suggested that | write to Squire Kay and obtain the price list of Sea Scamp, his newest design. | was told it had a G.R.P. hull and aluminium mast and would be reasonably priced. Back home | checked the regatta results again and discovered that Squire Kay had achieved 7th place in the R.M. World Championship (the highest place with a GRP hull) and he had also won the Champions Cup of 1987. Info Arrives | sent for a price list which came back by return of post. The price of the hull, keel and rudder was only £55 if purchased with 2 sets of panelled sails at approx £20 a set. This price seemed very reasonable compared to others with similar spec. and the regatta results for ‘87 seemed to prove the design. The price list said allow 6 weeks for delivery so to make sure | would have a boat ready for the start of the season. | sent off immediately for the hull, fitting kit and 2 sets of sails at a total price of £240 including postage. Kit Arrives Only 9 days later | received a letter telling me the kit was at my local railway station waiting for collection. | nipped down to the station and the porter got out a huge cardboard box “7> my name on it. When | got home | mpened the box and noted the hull was me” supported with cardboard Supports and the fittings had been Seely packed for the journey. | tM ecked all the parts and everything Seemed to be in good order. | studied ‘Te enclosed instruction sheets that Jute August Sea Scamp in working suit in a good breeze. night to try and work-out a plan of assembly. The instructions | must say leave a lot to be desired, but | was able just to understand roughly how most of it was intended to be assembled. | wrote back to Squire Kay with some questions about the instructions and he answered my queries and told me he will be writing a new set of instructions for Sea Scamp as soon as he can get roundto | then made two wood boxes 13in. x 14in. x 2in. deep for each half of the mould. | suspended the wood plug half way into the bottom moulded box and filled the box with Plaster of Paris and left it to dry for a week. | cleaned the top surface of the plaster and coated it with a thin layer of Vaseline. | fixed the top mould box to sit on the lower box and poured Plaster of Paris in and allowed it to dry. A week later | opened the mould and removed the wooden plug and placed the two halves in the airing cupboard to thoroughly dry. | cut a 1in. diameter pouring hole in the mould and screwed the two halves together ready for the lead to be poured. My friend Ralph Stockton helped melt and pour the Q9lbs of lead into the mould in his workshop, ‘Thanks Ralph”. Half an hour later we opened the mould and out fell a shiny lead with only a few marks on the surface to clean up. | drilled the 2 x 3/ 16in. holes through the lead for the fixing bolts and then covered the surface with Plastic Padding elastic. This was rubbed down with wet and dry using plenty of soap to smoothe the surface and given a couple of coats of spray enamel paint. Fitting Out | was ready to fit out the hull and the first job was to clean off the flash it. Assembly | had not ordered the lead keel as | already had some lead pipe and | did not want to pay the cost of postage for a lump of lead. | made a wood plug in my old lathe the shape of the lead and gave it several coats of sanding sealer. Above, rudder, bumper, booms and rigging wire. Below, the hull, with fin and stubmast with shroud plates fitted. Rigging Top left, hull with fin and rudder. Top right, wooden plug, mould box and finished lead. Above left, mast and gooseneck fittings. Note immaculately shiny deck. Above, sheeting of mainsail to the top of the mast. Two chrome from winch. Left, mast ring fittings were supplied and | fixed one at the mast join and the chord swivel for boom and extra forestay for safety. around the fin holes and to dry fit the hold the shroud plates, rudder posts and tie bars, and | used polyester resin with glass cloth to glaze in the fin to the hull. | found it quite difficult working up inside the hull looking through the hole in the transom, as | wear bifocal glasses. A lesson learnt early on was to cover the outside of the hull and around each hole to keep any stray resin from sticking to the gell coat on the hull. | made 2 off ‘/,in. wide by ‘/,,in. thick aluminium brackets to hold the winch and rudder servo and glassed and resined them in place within the hull. The fin had two brass bolts protruding at the bottom and the lead was pushed over the bolts 16 plug and 24 hour Araldite, and the Yin. diameter backstay tube was glued and crossed loop fore deck. Note fin. | drilled all the holes through the hull for the shrouds, rudder, mast stub and fixed each bit in place with a spot of Superglue. | used Plastic Padding P40, the type with fibreglass strands to The mast stub had already been glassed into the hull and the boom and gooseneck fitting were assembled with 24 hour Araldite and small PK screws. The lightweight aluminium mast had to be joined with a 2in. long aluminium and two nuts were tightened. | used a little Plastic Padding to flair in the lead-to-fin joint and sprayed the joint and lead with a final coat of paint. The instructions advise covering the joint between the hull and deck with car trim tape, but when | tested the joint | discovered it was not waterproof and | did not trust the tape to keep out the water. | covered either side of the join with masking tape and made up a small beaker of polyester resin and with a small old paint brush | sealed the join on both sides of the hull. When the resin had hardened | removed the masking tape and then covered the join with car trim tape to hide the join. | feel it is worth making the boat waterproof as possible, especially as | might use it in briny water (Poole Park, etc). | now made a stand to hold the boat so that | could erect the mast and rigging. other 6in. from the top with small PK screws. | made temporary fore and back stays to support the mast whilst rigging the shrouds. | followed the instructions by fixing the stainless steel fishing line top shrouds to the highest mast ring and taking them down and through the shroud hooks at deck level and back up to the lower mast ring where | made them off with a temporary join of Sellotape. | then made the permanent fore and back stays of stainless steel fishing line and with short lengths of rigging chord and bowsies. | was then able to adjust the shroud lengths making sure that the mast was vertical to the keel and finally crimping all the lugs tight. The mainsails are fixed to the mast with thin stainless steel wire rings and the outer end is clipped to the boom with an S hook. The sail is tensioned with a chord down haul and bowsie. | made a jib boom for each fore sail to make changing sails easier and to retain the sail adjustment. The jib booms are fixed down to the foredeck with a short length of chord to enable them to Radio Control Boat Modeller swivel easily, but | did not trust this chord to hold up the mast as well as the fore sail, so | made a thin stainless steel fishing line fore stay. The instructions made two suggestions on sheeting, one with an elastic tensioner and the other a closed loop along the deck. | have used the latter idea to keep all the sheeting problems above the deck. | bought a screw top plastic tub from ASDA for 83 pence and made a flat plastic plate 4in. x 4in. to fit around the tub and to enable the plate to be taped to the deck. The receiver and 5 cell battery pack fit nicely in the tub and the hole where the wires enter was sealed with mastic and PVC tape. For the hatch over the winch and rubber servo | used a sheet of clear asitate taped on so the | could watch the winch working. Sailing | have used the boat twice, both times with a good breeze on my local pond. The boat performed extremely well with a good turn of speed and responded quickly to the rudder. | used the working suit both times and with the 9 Ibs of lead and the 16in. of keel, she stood up well to the heavy gusts. Conclusion | think this must be the most reasonably priced RM kit with a good proven regatta record. The hull, etc. fitting kit and especially the sails are all very well made and carefully packed for transport. | will recommend this kit completely for anyone wanting an RM that won’t break the bank. My only criticisms were the poor instruction sheets which Squire Kay tells me he is updating soon, and the reed to seal the hull-to-deck join which was easily sealed with resin. | will not comment further on the sailing performance as it is my first RM, but in the right hands like Squire Kay and Dereck Priestly it has proved its worth. Address for more information is:Mr. Squire Kay, Hillside, Pincock Brow, Buxton, Chorley, Lancs. PR7 6LR. Top left, rear hatch with rudder and servo. Top right, stern showing rudder. Note acetate cover over rudder linkage to see what’s going on inside. Above, Asda tub holding receiver and battery pack. Winch and rudder servo can be seen in after hatch. Right, all ready for first trip to the lake with working suit of sails fitted. All photos: Richard Webb. July/August At last we get round to suggesting a few personal thoughts on tuning, not necessarily unique or original, they may prove useful and provide somebody with a bit of guidance. We also have a round up of some early season race meetings and personal experiences of a couple of the newest winches on the market. Finally they are out! The IMYRU 1 Metre rules are summarised here. Tuning The traditional place to start considering tuning is to recap on just where a yacht can sail relative to the wind. The oft used, and published, circle (Fig.1) shows that for any wind direction a yacht cannot sail from the centre of the circle directly into wind. There is a minimum angle ‘made good to windward’ of up to 45 degrees either side of the wind direction. This is with boats which are likely to be familiar to the typical radio sailor. ‘Scale sail’ and square rigged vessels could be considering angles of up to 90 degrees either side of the given wind direction. A boat with a centre board, like a dinghy, is likely to be at one extreme of about 45 degrees: whilst a well tuned keelboat like a 12 Metre, an A Class, or even a modern Marblehead could well be looking at up to 10 degrees less. The sector defined by this angle has been for a long time described as the ‘impossible sector’. It is the zone in which the wind will not flow over sails SO as to produce forward motion of the yacht. There is a narrow zone between VACHTING ? asks Mike Kemp A real mixture this time; Tuning, Races, the impossible sector and about 45 degrees which can be described as the windward sector. From 45 to around Results, and the latest news. 130 degrees can be called the reaching sector, and beyond that up to in the windward sector. It is in this narrow sector that a newcomer is likely to feel at his/her most ways of presenting maximum sail area to the wind when on the run. That, eye can compare a well set up yacht 180 degrees the running sector. Previous articles have mentioned combined with ensuring minimum under water resistance and smooth but positive steering is about all that can be done at this stage for running. Reaching can be improved by ensuring a proper main to fore-sail relationship and paying some attention to sail shape, flow, and twist etc. Windward Sector All of this attention is relatively insignificant compared to the sailing benefits of getting a yacht to sail well 36 inadequate. An untrained beginner’s with his/her own and have thoughts of; “‘There’s not much difference there”. When on the water, however, the expert’s yacht immediately sets off apparently almost dead into wind, whilst the beginner’s struggles even to sail at 45 degrees to it. And that with a lot of rudder applied! Why? There are a number of variables that affect windward performance depending on the rig design and configuration they can be adjusted with varying degrees of independence. Radio Control Boat Modeller serious designs now available are more or less ‘balanced’. This means that, no matter which class is chosen, a newcomer’s yacht is unlikely to exhibit any strange sailing tendencies induced by extremes of hull shape. Also, fortunately for many constructors; yachts, kits, and hulls One overall and very important factor in a yacht’’s ability to ‘point’ into wind is the position of the rig ‘Centre of Effort’. No matter whether the yacht is equipped with conventional or swing rig the C of E is largely dependent upon the position of the mast. Mast position is just about number one on any list of things to be ‘tuned’. now normally come with mast position(s) located, marked, or identified. These will usually have been arrived at by considerable experiment and thus be quite reliable. Mast Position We have many things in our favour these days. Model yacht design has developed to a point where most In such cases the point at which to Wind start is with the mast set in its designed position and rigged so as to be at right angles to the water line, or perhaps raked back at one or two degrees. The jib would normally be set so that its leach is just in front of the mast, a gap of about 5mmis likely. Whatever the rake it is important that the mast is perfectly vertical in the athwartships direction and not leaning to one side or the other. With some hulls you may find that this means that the mast is not actually at right angles to the deck. It is probably more important to have a straight line running up through the fin and mast than for the hull to be perfectly symmetrical about either the fin or the mast. Having said all this about asymmetry, such a yacht will never be at its best. Initial Settings Impossib e sector Once the mast and sails have been rigged attention can be turned to initial setting of sails and sheets. Several variations of the same theme are used and recommended by persons more Close reaching sector experienced than |. My particular basic arrangement is to pull in the winch Close reaching sector RE RE line until the main boom is ‘centrelined’. | adjust the jib boom until the ‘slot’ is just wide enough at the bottom to allow the four fingers of my clenched fist to fit between mast and jib leach. The effect is to give me a slightly wider slot than on many Running sector RU Left, Rhythm, extreme left, consistently climbed to windward in any touch of breeze. Below, David Chester’s new boat, a ‘Hush-Hush’, demonstrates its shroudless conventional rig. Almost instantly replaceable by a swing rig, it is possibly more effective. conventionally rigged yachts; it works so | leave it that way. Swing rigs seem to start with a slot of about half to three-quarters that on a conventional rig of a similar size. Sheet attachment points should be arranged so that the two booms swing out at about the same rate as the winch is operated. If there is to be any discrepancy | have found it best to ensure that the jib boom swings out slightly more than the main, thus opening the slot. If the main goes out first you are likely to find that it loses power while reaching. Trying It Out From now on you are dependent upon the weather. Initially you are looking for a steady wind of around 10 to 15mph. Ideally the wind direction should be directly on to the most convenient launching bank of your water. When these conditions prevail you are set to do an initial trial of your B suit. This is usually the suit provided when you first acquire a yacht kit, it is a pretty good choice because it operates over a wind range that a beginner can easily handle. Light winds can be a pain at first because many yachts adopt a ‘dead’ feeling, whilst heavier winds will make virtually any yacht work, irrespective of tune. For the first test voyage you should ensure that the rudder is properly 37 centred and that all the radio gear works. Many will say the yacht should be treated as a free sailing craft to Start with. | don’t subscribe to this idea, after all you have built it to sail under radio control and you will want to play immediately. Unless there is something drastically wrong with your initial settings you will be able to sail the yacht about under some form of control. Get used to steering the yacht as it goes away from you, the easy bit! Then get used to steering it as it comes towards you, the difficult bit! When you have developed sufficient control to return your pride and joy you can move on to trying to tune it. Position yourself roughly in the centre of the available sailing water, lay the Top, Ken Butler’s new 71 Metre hull, another multichine design, six planks this time. Right, the fleet runs away from the windward mark. Opposite top, tilting the yacht to get a view of the slot between main and fore sails. Opposite bottom, another way of checking sail shape by looking down the mast. transmitter down alongside you, set the rudder central, and the winch so that the sails are close hauled (pulled right in). Point the yacht at about 45 degrees to the wind, to the right or the left – it doesn’t really matter, and gently push it away from the shore. Watch it carefully and make a note of how it sails – write or draw it down if you want. Does it pick up speed and sail straight? Does it swing around and point towards the wind, and how quickly? Does it turn away from the wind? The chances are that it will do one or other of these things, but not more than one. When the yacht has sailed away into the middle of the water and given you a good time to observe its performance pick up the transmitter and sail it back to you. Reset the controls and go through the procedure again but this time set it off on the opposite tack. Once again make a note of the performance; and return it to you. What does all this tell you? Here are some ideas. : Sails straight on both tacks, deviating neither into nor away from the wind – well done, you ‘Z. are well on the way: read on. On both tacks, slowly swings around into wind until continuing to sail at a closer angle to the wind, only deviating as the wind strength varies even better, come and show me how you did it! 3. 38 Rapidly swings around to almost head to wind, stays there. with the sails flapping – you appear to have the C of E too far aft, first Cure is to move the mast forward slightly. 4. Continues to sail but swings away from the wind to a point lower than 45 degrees to the wind – chances are that the C of E is too far forward, first cure is to move the mast back slightly. Any significant difference between the sailing performance on one tack to the other, assuming that your rudder really is centred and is in line with the fin, is almost certainly an indication of a ‘lopsided’ rig. That is, the mast is not upright with respect to the fin. This should be corrected before any further tuning is attempted. With some yachts, where the hull is supplied with a mast tube ready moulded in place, you will not be able to move the whole mast fore or aft as appropriate. It is likely however that any turning tendencies will be less pronounced. In these cases, and with minor deviations on other yachts, you should try to effect a cure by simply raking the mast slightly. Slacken the forestay and adjust shrouds to achieve the mast movement desired. Notice that | have not suggested using the backstay to haul the mast back: | believe that it should only be used to control the shape of the mainsail. When the changes have been made repeat the sailing trials, once again making notes if necessary. Eventually you should reach a situation where the yacht will sail ‘hands-off’ on both tacks at between 35 and 45 degrees to the wind as you feel it. From now on tuning can be restricted to adjusting sail shape and the relative positions of the jib and main. In addition, from now on you will find it difficult to produce significant improvements in performance without some sort of ‘trial horse’ with which to compare. This is where being a member of a club can help, and where entering an open meeting can be even more helpful. There is nothing like trying a yacht out in competition with a number of others to show up its weaknesses. Sail Shape There may be some of you reading this who are about to comment; “What about the actual sail shape, flow, twist, belly, etc. A subject worthy of an article on its own, there is an easier and more convenient way – get your Radio Control Boat Modeller hands on a ‘Yachtmate’; an advert is usually carried somewhere in this magazine. This little slide-rule like device can help with basic sail shape settings, | occasionally get mine out when | want to return to some kind of sail shape reference point. | usually resort to it after | have had a frustrating time of ‘tweaking’ the sails only to have succeeded in completely wrecking the yacht’s performance. From your basic settings you will move on to what might be called ‘development’ tuning. At this stage, even if not before, you should rigidly stick to the rule of Change only ONE thing at a time. Having made that change try out the performance, preferably against another yacht which has had no changes made so as to make comparisons valid. The relative positions of Main and Fore sails can have a bearing on a yacht’s pointing ability, but not as much as the position of the whole sail plan. More significant is the slot’s effect on a yacht’s speed. One way of _ arriving atacorrectslotisto progressively close it until one can discern a backwinding affect of the jib on the main. This can be seen when a small crease begins to appear on the main sail about one third of the sail width back from the mast. This crease will come and go as the yacht sails at slightly different angles to the wind, also as the wind strength and boat speed vary. What is happening here is that, instead of bending the airflow so that is sticks to the back of the main sail, the jib is directing air into the back face of the main sail. My solution is to reach this point, then to release the jib setting until backwinding just disappears. Because a foresail is usually working at a greater angle of attack to the wind direction it can often be set flatter than a main sail. A good way to check the jib setting is to view the sails from the stern with the sails drawn into shape by a combination of gravity and wind. The all important ‘slot’ should appear even from this angle. To achieve such a shape many skippers, including me, fit a leach line (or topping lift) to take some tension out of the jib leach. Care has to be taken with such a line as it can very easily become hooked on spreaders and other protuberance from the mast. If this happens they can be much more trouble than they are worth. A Tale Of Two winches The coming of the 1 Metre Class, unless it becomes still-born through the efforts of the ‘Rule Makers’, is prompting an expansion of the range of winches commercially available. For the builder this is potentially a good result; for the established winch makers perhaps less so. What are these new winches like? The building of my Rhythm gave me a chance to take a look at a couple of the new products. One, the Whirlwind Low Profile, is the latest offering from one of the World’s leading suppliers; the other comes from Tony Abel, an established modeller new to this field. Tony Abel’s unit is the lighter and more compact of the two, it uses British made SLM case and mechanics and the Signetics NE 544 servo IC. The Whirlwind ‘Low Profile’ also uses the Signetics Chip but has an additional power transistor bridge output stage. It comes in a purpose moulded red plastic case which is indeed a low profile version of the familiar Whirlwind Olympic winch. The Abel gearbox is an all plastic gear affair equipped with a ball race around the output shaft; the Whirlwind uses a gearbox of Multiplex origin which has metal for all but the first driven gear, which is a fibre device. It, too has a ball raced output shaft together with a protective seal. Fitting the necessary electronics into the case is a close affair in both, though more of a squeeze in Tony’s. Both winches use a twenty turn cermet feedback potentiometer with suitable electronic ‘padding’ to reduce the effective output shaft turns. The Abel winch has three working turns for a normal transmitter stick movement, plus approximately half a turn each way as a result of trim movement. It has proven somewhat unstable at one end of its travel with some Transmitter signals. The Low Profile standard winch also provides three turns although it is equipped with a larger drum. The alternative Low Profile, the Super, has the facility to adjust its turns from less than two up to six or seven. Both winches are supplied with drums, the Low Profile has the smallest of the Whirlwind range, with a red centre. The Abel has a drum built around a standard servo disc with an aluminium plate top and bottom. This is one of the problem areas on this winch as there is insufficient room for a sheet to be fastened without it fouling on the top of the winch case. Tests In order to introducea little objectivity to the reviews | set up some very simple tests on my workshop bench. The power supply in each case was the same 5 Cell pack of 750 mA Hour Nicads. The no load voltage of this pack remained at around 6.4 volts throughout the tests, whilst the on load voltage varied between 6.35 and 5.98 volts depending upon current being drawn. Electrical measurements were made using simple digital multimeters and a hand operated electronic stop-watch was used for timing. The winches were controlled by a 27 Mhz Futaba Attack Receiver commanded by a compatible Sanwa Two channel transmitter. Note 1: The load placed on the winches was applied using lead castings intended for ballast weights. Although not particularly scientific | believe wy ‘August 39 their standard form, complete with a Futaba lead both winches retail at or around £44. The Whirlwind Low Profile Super, at the time of writing, is listed at £49.74 and gives the added bonus of a wide range of turns adjustment. Which should you choose? It all depends upon your pocket and your aspirations for winch performance! Racing Rhythm Having completed the Rhythm | was looking forward to finding a race meeting to try it out. Easter Sunday presented such an opportunity at Bournville with an open meeting for both R36R and 1 Metre yachts. Packing the Kemp family into the car demonstrated an immediate advantage of this class over some of the more common racing classes. Even the tall Suit; ready rigged on its mast, could be packed inside the car; removing the need for a roof top box. A removable fin allowed the hull to be packed into the boot leaving plenty of space for all ~ the normal family outing paraphernalia. It was a little disappointing to find that only nine entries had been received for this meeting, and only three of those present were 1 Metres. Vic Bellerson, our sailing OOD, put us on our honour to sail properly, acknowledge infringements, and do penalties accordingly as we would all be sailing together. An unusually straight wind, for Bournville, allowed a start and finish line close to the Clubhouse, a long beat to the narrow end to be followed by an even longer reach to the wide end, another across to the club house and so on. Long they represent a reasonable impression of some of the loads that might be placed on a winch in windy conditions. Load 1 weighed 1.82 Kg and Load 2 added a further 1.85 Kg to give a total of 3.67 Kg. The loads were suspended directly on the drums supplied Note 2: using a length of 80lb. braided Dacron line. The times shown for winch travel are the average of about six measurements in each case. No time is shown for the Abel winch with Load 2 for the simple reason that it made no attempt to move! Never the less the electronics tried to respond, as shown by the increased current drawn. The Whirlwind winch also failed to complete its full three turns under this load, it consistently completed approximately 2.8 turns in around 19 seconds. It just remains to point out that in 40 Chris Dicks’ Magik has a very pronounced flare developing over the front third of the hull. courses of two triangles and one Sausage were set which allowed plenty of position changing to take place. The wind strength was such that Vic and Elizabeth Andrews were carrying over 1000 square inches of sail on their R36R yachts. Although the Rhythm proved to be very competitive reaching and beating it was relatively under powered off the wind – there was little that | could do as these ‘bedsheet’ equipped R36Rs kept overhauling me down the long running leg. Dave Andrews and Stan Adcock, both from Leicester, were sailing Harvey Middleton’s Impala 1 Metre design and showed that it too can be competitive with 36’s. Rhythm ‘..IC’ at this stage is still built to the Naviga rule, | shall not be changing it until the IMYRU committees have finished carving the rule about. There were rumours about what the eventual rule would look like (see elsewhere in this column); several proved to be true and include a larger top suit area of around 820 square inches. To move the new yacht even closer to the existing R36R there will Radio Control Boat Modeller be a shorter fin, with draught that will have to be measured from the waterline. General opinion of this latter point was that fewer things could be guaranteed to put off the beginner than having to find a club with a measuring tank to get registered. It has been suggested that certain IMYRU officials feel that the simple expedient of measuring with a box instead of a tank, such as the 36R method, produces a too intellectual design formula for them to handle! We shall see. What is certain is the R36R yachts and 1 Metres can be sailed competitively together. Under light wind conditions the R36R would appear to have the edge, as the wind picks up | believe the 1 Metre will start to shine – go on, build one! They Are Out! inspection of the fibres. A coloured gel coat may be used, so may coloured paint finishes on the outside only, one tapered booms, and other similar ‘Hitech’ accoutrements. assumes. Fin and rudder materials are unrestricted. are permitted with one for the rudder Mast construction materials are limited to wood or aluminium alloy and be basically circular in section without any taper. They must be at least 10.9mm in diameter, may be keel or deck stepped and supported bya fairly closely defined set of conventional rigging. The rigging regulations are framed so as to very effectively prevent the use of swing rigs, curved or Below, the Abel winch shows the tight squeeze for the electronics and the all plastic drive train. Only two channels of Radio Control and the other being specified for synchronous sheeting control. The sail plan has been designed by our own Naval Architect and sailmaker; Graham Bantock has devised a set of sails that equip the yacht with slightly more sail, in proportion to length, than the Marblehead. Three fractional rigs are specified and designed to cover between them wind speeds from O to about 10 metres per second( that is from O to 22 mph). The three rigs have areas of approximately 0.53 square metres, 0.36 sq.mt., and 0.24 sq.mt. that is 820, 560, and 370 square inches respectively. In essence the arrangements for marking, measuring and certifying these new yachts are the same as now apply for Marbleheads. It remains to be As | write this | have just received an advanced release of the 1 Metre rule; it is possible that many readers will have seen them by the time this reaches the book stalls. However| will summarise some of the key points here, just in case. If you want an official copy, get in contact with the MYA Supplies Officer, David M Hackwood, 10 Grangewood, Coulby Newham, Middlesborough, Cleveland, TS8 ORT. The Rating Rules will be supplied together with the appropriate registration regulations. The intention of the rule is to encourage development of a class to provide interesting racing for RC yachtsmen who want to buy a kit or even a ready made yacht. Hi-tech construction and exotic materials shall be avoided in this type of class, to this end there are maximum and minimum figures for draft and weight of fin and bulb. In addition there is a minimum all up weight and a very closely controlled seen how successful IMYRU and its constituent bodies will be at introducing the first NEW International Class yacht for years. Personally, | hope it succeeds; | really love my new little boat. A Ranking We Will Go Part One The first of the 1988 ranking races took place at the Cotswolds Club’s water just outside Cirencester on the last Sunday in March. Using one of several lakes in the water sports park at South Cerney, the Club also sails ‘full-sized’ dinghies and is equipped with a new Clubhouse usefully close to the water. An unexpectedly small number of entries had been received and twenty two eventually were called to the briefing by Officer Of the Day, John Osborne. Skippers were divided into three pairs fleets for initial seeding races; thereafter two fleets of ‘one design’ set of sail rigs. In comparison with the Naviga yachts were raced with the ‘three up inspired rule that prompted Rhythm, a good, if slightly tricky, wind races were conducted at a fairly leisurely Impala, and some other designs this rule sets a draft limit (from waterline to three down’ system operating. Despite bottom of bulb) of between 300 and 350 mm. A fully rigged and equipped yacht must have a minimum weight of 4.0Kg, with the detachable fin and bulb limited to between 2.2 and 2.5Kg. The yacht must have a monohull without tunnels, hollows, etc. with an overall length of 100Omm maximum, and a resilient bow bumper projecting at least 10mm forward of the foremast part of the main shell. Hull construction techniques are free but materials must be chosen from wood, plywood, glass reinforced plastic, vacuum moulded sheet plastic and film covering materials. The materials may de used in isolation or in mixtures but any resins used for actual laminating of GRP must be clear so as to allow July/August 41 Left, both these new winches are about the size of a Club-mate Derek Priestley’to pilot until they had to depart early for the long journey back up the M5/M6. conventional servo. Below, robust, almost all metal geared box of the Whirlwind winch, and electronics layout. A Ranking We Will Go Part Two Second in the 1988 season of ranking races was the Eastern District event. Chelmsford’s ‘Hatfield Trophy’ on April 24th at Channels Golf Club was chosen to receive this elevated status. Another unusually small entry of 18 skippers lined up under the control of OOD Norman Hatfield for a brilliantly sunny, windy, but bitterly cold day’s sailing. At the briefing we were informed that we were to be subjected to a day of passive pace and lunch was taken after the third of the seeding rounds. The original intention was for everyone to observing, which no doubt raised some fears of unjust decisions and big brother type oppression in the minds of have twelve fleet races, thus being presented with the option for two many skippers. Our minds were put at rest to a certain extent by the fact that discards. Because the leisurely pace was maintained during the afternoon Norman was assisted, all day long, by three permanent observers. Rod Latham, Tony Bowers and Oliver Lee and races were punctuated by a few protests which, if one was not involved, seemed to take for ever to who patiently, and quietly watched the proceedings through one non-scoring settle this target was not met; even by seeding round and nine scoring fleet sailing beyond 5.00pm. Protests were dragging out so much that some were races. Whether any skipper was disqualified, without us knowing is difficult to judge from the score sheet, suggesting that there should be a strictly held time limit for settling such matters. Despite a little ill feeling as which shows no less than ten Did Not Start, Did Not Finish, or Retirement the result of the delays and subsequent decisions not going the way of some of the protagonists the scores spread over six skippers. It is known that some of these were DNS scores so one can only conclude that meeting was conducted in fairly good skippers, rather than be disqualified, took a retirement score having not had humour. Among the yachts making their first appearance in such meetings was the successor to my Sula Bula – Bill Sykes “Ski-Boat”’ – being sailed by Graham Elliot from Birkenhead. Looks quite attractive and has more rounded sections which might help in the lighter conditions. Several new ‘HushHush’ designs were to be seen, those of builder lan Cole and David Chester sporting the new unstayed conventional rig for ‘B’ suits and below. Based on an alloy casting and a tapering Carbon Fibre mast this development would seem to offer the best of both the swing rig – for tall Suits – and the conventional rig. Using a common sheeting system and a pair of mast sockets it is almost as quick to change rigs as with the, by now, well known swing rig which is still carried for the tall or ‘A’ rig. Although David Chester only took delivery of his new Hush-Hush at this meeting he sportingly handed it over to Fleetwood ’ the opportunity to take the alternative penalty. There are still unanswered spin-offs from the Passive System. All the foregoing aside, the racing was, in general, very keen and close. There were something like 75% of the field who should have been in the A Fleet, unfortunately that fleet could only accommodate 9 or 10 boats at a time, so there was a constant and keenly contested stream of promotees and relegates. The Easterly wind, apart from making the starting green an uncomfortably cold place to be, gave some ‘interesting’ B suit conditions. The small group of trees on the lake’s Easterly shore shredded the wind into an ever changing set of streamers across the lake. At one time or another all the leading skippers were led into doubting their sail trim, as yachts appeared to sail into patches of treacle. The windward mark was the scene of many disappointments and normally avoidable infringements. The inevitable eventually happened, after a morning when it looked as if he was going to be thrashed, Graham Bantock eventually emerged as the winner again. Chris Dicks sailed his new yacht, a slim looking device with Right, another NAVIGA sail equipped 1 Metre, an Impala being sailed by Dave Andrews. 42 pronounced bow flares, called ‘Magik’ into second place ahead of Peter Stollery. Radio Control Boat Modeller Another shot of the Chris Dicks’ Magik. Even the best sails can have wrinkles, seen earlier in the day on this boat, however trimming gets rid as can be seen in this shot. The League Season Starts Part One The league season got under way on one cold and snowy Sunday in March. The 13th, ‘Mothering Sunday’, saw the first 1988 Radio Marblehead League meeting on Larkfield Tarn, the home of Leeds and Bradford Club. Twenty Two had entered, all but one of whom started the Webster Memorial Trophy in an unusually North Easterly wind which had everyone wrapping up to keep warm. As the morning progressed this wind rose to a point at which some of the two fleets changed down to ‘B’ suits. A course was set to start at the leeward end, beat to the Clubhouse, reach back to the start mark, and beat back to a Clubhouse end finish. Squire Kay proved to be dominant despite continuous harassment by Mike Ewart and myself, while Dave Hollom played a distinctly undercover operation to end the day in second place. Previous rain had made the lakeside very muddy and slippery causing skippers to spend as much time watching their footing as their yachts. Some were less than successful in maintaining an upright position; Mike Ewart (Dovecote) managed to slip into the lake and fill his waders, Squire Kay (Ashton) had a lucky escape while launching, and Dave Hollom (Leeds & Bradford) sat on the bank several times. There followed several unkind comments about the brown stain on Dave’s trousers suggesting close encounters – of the rule book kind – with Squire! Among other notable competitors was MYA Chairman Peter Maskell who claims frequently that his first love is sailing Vane guided ‘A’ Class yachts. At this meeting he was ‘road testing’ a yacht – David Chester’s ‘Ecky Thump IV’ – with sufficient success to part with an undisclosed amount to become the proud owner of a black No Secret. Despite increasingly intense snow during the afternoon racing continued to about 4.00pm, by which time all surviving skippers had completed six fairly long races. After packing away and a welcome short rest in the clubhouse lounge while results were computed the Trophy was presented by OOD Terry Costigan to Squire. No further prizes were presented despite a slightly higher than normal entry fee. Instead, in line with suggests from MYA Council that such events might make contributions to charities, we had raised over £100 for Stoke Mandeville hospital. The Season Starts – Part Two Spring is a busy time for Marblehead skippers, with a wealth of events from which to choose. Observant readers July/August 43 might have noticed that | tend only to report events in which | sail and, unless | can get away with it, these tend to be at fortnightly intervals. Thus the next Marblehead league meeting for me after Leeds was a meeting on my own water, Dovecote. Sponsored by the Company of a Club Member, Car and Tyre Services of Wolverton, the Whyte Trophy meeting has for several years given skippers a chance to warm up ready for the coming season. In 1988 it had to share the 10th April with two other RM events, an A Class Vane National Championship, a 10 Rater Vane District Chamipionship, and a R36R League meeting. It was not really Surprising that there was a low entry of seventeen skippers. Although the preceding Saturday morning saw snow falling, Sunday dawned bright and sunny with a good ‘working suit’ wind of around eighteen miles per hour from a South Westerly direction. One or other of the Fleet systems has become almost universal at such meetings but becomes less practical with such a small entry so the decision was taken to run an old fashioned schedule. One major difference was that the designed size of race was for twelve boats – giving skippers the option of twelve races each out of the total of seventeen. Although one skipper failed to make the start and another retired with a broken gooseneck after three races the water seemed to be constantly crowded. Unfortunately the wind was just a little too westerly to allow a Port biased Start line that could be sighted from the shore. Consequently every start saw a great pile of yachts jostling for the prime Starboard end spot. There were rich rewards for the skipper who made it and then tacked away onto Port eventually to come into the first mark on Starboard. At least one skipper made it in every race with the inevitable chaos as Port tackers were left with nowhere to go. The one redeeming feature of all this was that the first mark was within six or seven boat lengths of the shore so everyone had a good view of what they were doing. Perhaps it was the weather, it may have been that OOD Mike Ewart kept us all on the move with very little delay between races, but even some of the strongest proponents of Fleet racing made no significant noise about sailing a schedule. Perhaps they were too busy trying to find a part of the course that was not already occupied by other yachts. As the day wore on it became obvious that, barring some major catastrophe of sinking or rule infringement, the Whyte Trophey was going to return to the Bantock household. Second place also looked as if it might be securely in the grasp of Yacht Builder lan Cole. Several 44 skippers tried very hard to prevent the inevitable, even to the unintentional (I assume) near sinking of lan’s new Hush-Hush following a collision with Alan Graham. Racing actually ceased at about 3.30pm which left plenty of time for a few ‘beer races’ while the scores were being totalled. With a minimum of twelve races behind them it appeared that all returned home having had their fill of racing. A somewhat under-the-weather Mike Ewart did the honours and presented the Whyte Shield to Graham Bantock, fresh from his success in the Canaries at Easter. Fellow Chelmsford Club member lan Cole sailed his somewhat battered green ‘Hush-Hush’ into second place whilst | squeezed my ‘Low Tech’ Sula Bula into third. After a longish spell out of the top group ‘Mr Whirlwind’ Dave Andrews returned with a ‘Hush-Hush’ fourth place; Elizabeth sailed her new yacht, the exLouise Smith No Secret ‘Chat Noir’, into 6th place close behind Alan Graham’s similar craft. Conventional rig fan Mike Golding has re-acquired the original ‘Manhattan Mist’, Tracer, in place of his ‘Hush-Hush’ and felt a little happier with its performance – could it be that the new Bantock/Cole creation really is only suited to swing rigs?. Buyers Beware Model yachting has become much more commercial over the last few years; by that | mean there are now more sources of commercially produced yachts, kits, fittings, and sails. As in all forms of specialised supply the quality of product can vary considerably. Some names become well known by virtue of their own performances using products of their own design and manufacture. It is in their own interest to make sure that their products are of the highest possible quality consistent with what customers are prepared to pay. Others become known by having been in the business for a long time; these can usually be relied upon because they Radio Control Boat Modeller to lose more than one potential customer. 1988 Season – Ranking List Update The Marblehead Ranking List has now been updated following the two meetings mentioned above. Here is summary of the current top ten, if you want a copy of the complete list, it is available by subscription for six issues by sending a cheque for £2.00 (payable to the MYA) to: lan Taylor 115 Mayfield Avenue, London N12 SHY Graham Bantock is still at the top of the list with a perfect score of 100%, he still has yet to be beaten ina ‘serious’ race in over two years! There have been a few changes beneath him, however. Just to remind you, the idea of the ranking race system is to provide the MYA with a continually updated list from which to select official team members for entry into International events. Happy News We end this issue with some bad news and some good news. The Bad news is that Model Shops do not seem to be taking up the cause of Radio Yachtsmen and stocking some of the kits now appearing one the market. The Good News is that one of the suppliers, lan Cole, has decided that in the absence of interest from the Shops he is prepared to pass some of the mark-up available for the retailer on to the modeller who orders direct from lan. would have not survived for so long had they been purveying total rubbish. As new niches open up new suppliers make an attempt to break into the market, often using lower price as their selling point. One of my newer Club colleagues is currently becoming rather dispirited with his first Radio Yacht as bits of it Opposite, the latest underwater shape on the latest Stollery Bees. Top, the tilt and trim technique, as demonstrated by a master, Chris Dicks. Above, the Rhythm, seen climbing to windward on page 36, has been able to squeeze ahead at the marks by now. All photos: Mike Kemp. commercially supplied Radio Yacht equipment was a failed gooseneck considerable loads that can be placed on a kicking strap by B and C suits. The design of this assembly put these loads onto the small diameter tube such that it was torn off the large tube. Soft solder is just not suitable for this application, in fact the only application for soft solder in a Radio Yacht is inside the receiver and servos for assembly which utilised one smaller electrical connections. begin to fail. He is suffering that stage of disappointment we all go through with our new hobby when what we have proudly created emerges as somewhat inferior to what the ‘regulars’ are using. The latest example of less than satisfactory diameter tube soldered to a larger tube. Supplied in a very impressive chrome plated finish to contrast nicely with a Carbon Fibre mast the achilles Some of us make our own fittings not just because we are mean, poor, or even budding Model Engineers, but because we prefer to trust our own neel of this device was that the work when it counts – in the middle of assembly used soft solder. Anyone a wind tossed lake. who has sailed a Radio Marblehead for some time will be aware of the July/August Let suppliers of such poor materiel beware, it only takes one such failure The Result is to reduce the Rhythm 1 Metre from £225 to around £190 for the very complete kit that | reviewed recently. Similar reductions apply to the individual packs that go to make up the yacht. An Anagram, the ‘State of the Art design’ wooden Marblehead, reduces from £260 to around £220. Once again the individual packs are also reduced in a similar proportion. Ah well, the Model Shop’s loss is our gain! Next Time A number of race reports could reveal what are going to be the ‘boats to beat’ during 1988. R36R and 1 Metre yachts will be mixing it at Scarborough Mere during the Primrose Valley Modeller’s holiday week – it could be an interesting test. The district Championships for RMs will have taken place as well as the Nationals for R36R yachts. Lastly, Gosport is the venue for this year’s MYA Radio Marblehead National Championships, your columnist will be there trying again to win it – watch this space! 45