Boat Modeling by Vic Smeed – Fourteenth Impression1976

  • This book sets out to cover the whole subject of present-day model boating in as comprehensive a manner as possible. Naturally, in attempting to embrace every aspect of so vast a subject in one small volume, some items must inevitably suffer by abbreviation, and, in looking through what has been written, I cannot see one single subject on which I would not like to have written more!
  • However, in every case the important points are covered and the best or most popular method of construction is given if there is insufficient space to detail several methods. Yachting enthusiasts will, I fear, feel that too much space is devoted to power boats—it is little comfort to consider that power boat fans will undoubtedly feel the reverse!
aTECHNICAL PUBLICATION it aes l en ra Hs * . BOAT MODELLING V. E. Smeed An introduction to the fast growing hobby of model boating by an author who has proved his versatility by a number of successful designs covering most types of model and has wide experience of the most frequent difficulties confronting the newcomer through the medium of readers’ queries to ‘Model Maker and Model Boats’ of which he is Editor. Model and Allied Publications Argus Books Ltd, Station Road, King’s Langley, Hertfordshire, England Argus Books Ltd, Station Road, King’s Langley, Hertfordshire First Published Second Impression Third Impression Fourth Impression Fifth Impression Sixth Impression Seventh Impression Eighth Impression Ninth Impression Tenth Impression Eleventh Impression Twelfth Impression Thirteenth Impression 1956 1956 1957 1958 1960 1962 1964 1966 1968 1969 1970 1972 1973 Fourteenth Impression 1976 ISBN 0 85344 066 2 © 1976, Argus Books Ltd. Text © 1976, V. E. Smeed All rights reserved Printed in Great Britain by The Garden City Press Limited, Letchworth, Hertfordshire SG6 1]S Contents 4 Introduction 5 Chapter One A LOOK AT THE SUBJECT Chapter Two TOOLS AND MATERIALS 10 Chapter Three HARD CHINE HULLS 13 Chapter Four ROUND BILGE HULLS 19 Chapter Five OTHER TYPES OF CONSTRUCTION 26 Chapter Six SUPERSTRUCTURES 32 Chapter Seven FITTINGS 36 Chapter Eight YACHT FITTINGS 43 Chapter Nine FINISHING 51 Chapter Ten INTERNAL Chapter Eleven STEAM ENGINES 61 Chapter Twelve ELECTRIC MOTORS 64 Chapter Thirteen HYDROPLANES AND SPECIAL MODELS 66 COMBUSTION ENGINES 54 70 Chapter Fourteen “ OPERATION Chapter Fifteen RADIO. CONTROL 72 Appendices M.Y.A. Rating Classes 719 M.M. Class Rating Rules M.Y.A. Affiliated Clubs Power Boat Classes, etc. M.P.B.A. Affiliated Clubs British i/c Engines British Electric Motors Glossary , 80 81 83 85 89 90 91 Introduction This book sets out to cover the whole subject of present-day model boating in as comprehensive a manner as possible. Naturally, in attempting to embrace every aspect of so vast a subject in one small volume, some items must inevitably suffer by abbreviation, and, in looking through what has been written, I cannot see one single subject on which I would not like to have written more! However, in every case the important points are covered and the best or most popular method of construction is given if there is insufficient space to detail several methods. Yachting enthusiasts will, I fear, feel that too much space is devoted to power boats—it is little comfort to consider that power boat fans will undoubtedly feel the reverse! Model Boats can justly claim to be the oldest of all working models, and have developed through the centuries until nowadays their design, construction, and operation are frequently held to be a science. Science, of course, is nothing more than organised common sense, and I have therefore stressed the practical side of the hobby in this book, bearing in mind that each month sees new faces at the waterside. If the book helps those new faces to become familiar to existing enthusiasts, primary object will be achieved. V. E. SMEED its Chapter One HE expression “model boats” covers an astonishingly wide field. On the one hand are the small power craft and yachts seen at almost any time in the hands of youthful owners at the local park pondside, and on the other are the enthusiasts’ highly efficient racing machines and the research models which contribute so much to techmeal ad- vances in the full-size world. Between these extremes lies a fascinating selection of classes—so many that it is perhaps advisable to group them as conveniently as possible at the outset of this book. Power ‘Craft There are various forms of power plant in common use, and various types of boats to use them; practically any combination can be used, so let us first examine the available means of power. (i) Rubber—a somewhat neglected propulsive force, yet one which is inexpensive, simple to operate, and capable of giving excellent performance. (ii) Clockwork—still the chief motive power of toy boats, but, in the form of converted clock or gramophone motors, not to be despised by the serious modeller. (iii) Electric motors—widely favoured in all types of model where high speeds are not required. Clean, cool, quiet, and uncomplicated, excellent for speed control, etc. Disadvantages’ are weight and space requirements for batteries or accumulators, and relatively high operating t costs (q.v.). (iv) Petrol engines—excellent for many models unless reversing is required, when a relatively complicated clutch is called for. Good speed control, fairly simple operation provided the ignition system is thoroughly water-proof. (v) Glowplug engines—at one time these were only used where the last ounce A Look at the Subject of performance was required; now fitted in many boats, but careful protection of the structure against fuel is necessary. (vi) Diesel engines—more correctly expressed as “compression ignition’ engines; these have done much to bring about the recent tremendous increase in model power boat popularity. Straightforward to instal and operate, but speed control is limited and steps must be taken against fuel soakage. (vii) Steam plants—still enjoy.a certain popularity though a little bulky and heavy for the power produced. Flash steam and advanced engines are used even in hydroplanes; heat and “mess” a disadvantage for radio control. (viii) Jetex motors—suitable for special models only, but quite simple to fit and operate. (ix) Jet motors—have little application in model boats and few examples have been seen. Types of Boats It is rather difficult to draw an exact line between some classes of models, but the following list embraces the entire range in general terms. (i) Sport models—usually semi-scale in appearance but simple in construction, may be powered by any of the above forms of propulsion. Size varies from a few inches to five or six feet, but two to three feet overall is most popular. (ii) Semi-scale models—the definition of “semi-scale” is normally a model which, if scaled up, could conceivably be a seaworthy full-size craft. The ex~pression ‘“‘near-scale” is usually applied to a model based on a prototype but usually simplified. Such models constitute the great majority of the small craft afloat today, and can resemble any type of vessel from launches to liners or warships. Most forms of power apply. BOAT MODELLING 6 \ CAMBER —_———- im SHEER OEADRISI TUMBLEHOME! TILLER RAKE : vias RUODE|7 ITLES RUBBING STRIPS OR RUBBERS SHAFT TUBE SKEG OR iN FRAME PROPELLER ssc SHELF OR HINE FREEBOARD ORAFT LWL(LOAD WATER LINE) (iii) Scale models—may be accurate representations of any size of virtually anything afloat. Electric power is most frequently used, except for fast launch types, when diesels predominate. (iv) Steering models—used in competitions, these are frequently specially designed to maintain straight, predetermined courses, and include reasonable draught with large underwater fins and little side area above water-level. Most forms of power are suitable, but accur- ate speed control is an advantage. Length is usually three to four feet. (v) Airscrew-driven hydroplanes—fre- quently simple models, and popular because no complicated drive is involved. Usually fitted with diesel motors, fast and exciting to operate; the European record is well over 100 m.p.h. (vi) Hydroplanes—a specialised branch of model boats, rarely using anything but i.c. engines and usually run tethered. Fast and exciting, but requiring skill. (vii) Special models—submarines, auxiliary sailing vessels, and unorthodox models generally. Operated for sport or experimentation. ‘ee. GARBOARD ANGLE ©Ow STERN (viii) Radio-controlled models—these can be of almost any of the foregoing types, provided that sufficient room is available for the necessary equipment, but far and away the most popular are the semi-scale hard chine launch types of 30-40 ins. length. Sailing Craft Most sailing models nowadays are Bermuda rig racing yachts, and there are six official classes built to special rules (see appendices). In order of size, these are as follows : “A” CLASS. Built to a special formula, “A” boats are normally between 6 and 7 ft. long and between 50 and 70 lb. displacement, with a mast up to 8 ft. in length carrying a sail area averaging around 1,650 sq. in. 12 METRE. Scaled at 1 in. to 1 ft. from full-size craft, giving a length of around 70 in., this class is now virtually non-existent. 10 RATERS. These boats are also built to a special tule and approximate 6 ft. in length, weigh somewhere between 25 and 30 lb. A LOOK AT THE SUBJECT and carry a sail area of roughly 1,100 sq. in. 6 METRE. These boats are the nearest approach to scale model yachts but because of the complicated rule are no longer very popular. Length is normally a little over 5 ft. displacement in the order of 32 or 33 1b., plus a crew weight of 2 lb., carrying somewhere between 1,100 and 1,200 sq. in. of sail. MARBLEHEAD. Of American origin, Marbleheads are built to the simplest specification, the main features of which are a maximum length of 50 in., and a maximum aail area of 800 sq. in. Displacement is normally between 20 and 24 lb. 36 in. RESTRICTED. The smallest recognised class, the basic rules being that the hull must fit into a box 36 x 9 x 11 with a maximum displacement of 12 lb. Sail area is unlimited. Three of these classes are recognised internationally, the “A” class, the 6 metre, and the Marblehead; the last mentioned is probably the most popular class of model yacht at present in existence. Yacht builders are advised to contact their local clubs before finally deciding upon a design, since few clubs race every class of model, and there is little point in producing a class boat for which there is no local competition. There is one popular unofficial class, this being the Half-Marblehead, 4M, or as it is normally known, MM Class. This was introduced by MopEL MAKER at the beginning of 1955, and is thus a relatively recent innovation; mneverthe- less, an enormous number of these models are being sailed. The primary aim was to encourage newcomers with a small and inexpensive racing design, and the chief rules are an overall length limited to 25 in., and a maximum sail area of 216 sq. in. The full rating is set out in Appendix II. Naturally, sport models are found in the world of sail, but the modern trend is to build class boats even for pleasure 7 sailing, or to break right away from the Bermuda rig and build semi-scale or scale models of schooners, yawls, barges, and even square-rig vessels. The size of such models is again a question of the builder’s taste, and may vary from a few inches to several feet. The only remaining class of sailing model is the radio-controlled yacht; the Model Yachting Association recognises all vane class for radio sailing, with the prefix R—RA, R10r, R6m, RM, and R36r. Of these by far the most popular is the RM, where a total radio weight of up to 2 Ibs. is customary. Control systems are men- tioned in Chap. 15. Competitions A very diverse range of competitions have become standardised for model power boats, and there is no doubt that such contests add considerably to the pleasure given by the hobby. Most builders eventually reach the stage of wanting to compare their models’ performances with those of other enthusiasts, and this is made easy even for the lone hand by the natural friendliness and the spirit of good-natured rivalry common to all boat fans. More can be learned by attendance at one competition than in twelve months’ work on one’s 8 BOAT MODELLING FIG. 3 (left): steering cB) competitions mounted on on buoys. eo Markers sticks or for are carried ~ FIG, 4 (below): A_ typical course for radio control steer- ing events, 2: } SUBMEAGED BvOYs FOR OLEP WATER own, and a large number of clubs exist throughout the British Isles, all of which run competition programmes throughout the year. “Even if you can only get along to three or four meetings a year, joining an established club is well worthwhile; a list of clubs will be found in Appendix III and V. The normal competitions for model power boats are: (i) Nomination event—this is usually limited to boats with speeds of less than 12 m.p.h., and consists of a straight run over a course of 50 or 80 yards. The competitor has to nominate the time his boat will take to cover the course, and, naturally, the boat with the smallest error wins. Success in this calls for a reliable boat capable of steering a straight course, and with machinery which can be confidently reset at the same r.p.m. at any time, plus, of course, the ability to estimate wind effect, etc., which comes with practice. TEER! MARKERS & SCORING (ii) Steering event—in this, the boat covers a course of 50 or 80 yds. towards a set of markers spaced 3% ft. apart. Scoring is 1, 3, 5, 3, and 1 (Fig. 3). The same model requirements as above apply. (iii) Speed events—these are run with the models tethered to a central pylon. Line lengths and strengths, model classes, and speed records are given in the appendices, but it may be mentioned here that these events are virtually entirely given over to hydroplanes, (iv) Radio control steering event—here the models are required to steer between pairs of buoys set out in a course as in Fig. 4. Points are scored for passing between each pair of buoys, with smaller scores for missing on the inside or outside, depending on the position of the buoys in relation to the course. In addition some of these competitions include points for demonstrating “special effects” and speed control, after the course has been completed. The competition may also be broken down into sections segregating the various motive powers or the varying degree of control fitted, ie. separate approx, | AO FT, g) a 6 (ae) from boats may be those having rudder, reversing, and _ other engine speed, controls. (v) Radio control speed runs—usually a triangular or figure-8 course, with no real steering hazards. Three classes of i.c. engined boats and two electric classes are recognised—0-23, 23-5, and 5-30 c.c., and up to 30 and 300 watt. Sailing START 3 & Frish \S rudder-only Competitions There are few variations in competitions for sailing craft, all of which are races. A LOOK AT THE SUBJECT (i) Races on lakes, etc., are overwhelmingly the most common. The “American tournament” system is employed, ie. boats are raced two at a time, but every boat meets every other entrant. Each pair make a beat to windward (into the wind) for which the winner receives 3 points, and a run to leeward (downwind) for which the winner receives 2 points. A complete race by one pair (once up and once down the lake) is termed a “cheat” and a complete series between all pairs a “round”. (ii) Races on open water—these are very infrequent and are difficult due to the speed of modern yachts. Each competitor sails his model round a triangular course, using a dinghy to re-trim. As many boats may perform as can be conveniently sailed. (iii) Radio control races—rules are based on full-size yacht racing rules ; yachts sail round a triangular or rectangular course and may not be handled or touched after starting. Superhet radio equipment is necessary to sail boats together without radio interference; normally boats sail in pairs but up to twelve or fifteen take part in occasional mass races. Lighter, improved radio equipment is attracting more people to this type of sailing, which takes considerable skill. Organising Bodies There are two main controlling bodies covering all model boat activity in this country, the Model Yachting Association, which deals with sailing craft, and the Model Power Boat Association, which governs power models, racing hydroplanes, etc. The work put in by these bodies is entirely on a voluntary basis and the amount of work done is of considerable value to all enthusiasts, although it may not always be evident. Apart from formulating regulations 9 and carrying out other committee business, both the governing bodies organise a full annual programme of meetings, which are distributed geographically in order that the difficulties of travelling are shared by enthusiasts in various parts of the country. As an example of this, the premier yachting event of the year is the British and Open A Class Championships, which lasts for a week, and is held in the north of England one year and in the south the next. Naturally, the authority of the central bodies is broken down over a wide area by means of numerous clubs who affiliate to their respective parent organisation. Members of affiliated clubs enjoy the benefits obtained for them by the hard work of their officials—benefits which range from the use of stretches of water to comprehensive insurance, etc.—and are of course able to participate in official events without difficulty. In the case of yacht clubs, where the models are built to strict specifications, each club is equipped with a measuring tank and has an official measurer who fills in a rating certificate for each new model. Without a rating certificate the model has no official’ sail number and cannot enter into official races. Similar functions are carried out by power boat officials. “Lone hand” modellers are recommended to get in touch with their nearest club, where, for what is normally a nominal subscription, they may share in the advantages of organised activity. If, however, you live in an isolated locality and operate entirely alone, it may still be an advantage to join a club as an inexpensive way of obtaining insurance, etc. though, in fact, many insurance companies will offer third party cover for an individual for a very nominal sum. Most local councils insist on such insurance cover for modellers operating boats on their waters, the cover being usually £50,000 minimum. = | 10 Chapter Two number of tools required to build a model boat will vary considerably with the individual as well as with the type of model under construction. For this reason the following are lists of more or less minimum requirements— some builders will, no doubt, make do without some items, while others. will be able to work better with additional tools not mentioned here. For the average, simple hard chine launch type, the following are suggested. (1) Small tenon saw—there is an excellent 7 in. saw with a hand-brush type of handle available cheaply in multiple stores. (2) Junior hacksaw (Eclipse) for both wood and metal cutting. (3) Fret saw. (4) Small plane. (5) 4 in. chisel. (6) Light hammer. (7) One or two screwdrivers. (8) Hand-drill, three or four assorted drills, and a rose countersink. (9) Pliers, preferably taper-nose. (10) One or two small G-cramps. (11) Try-square. (12) Sharp knife or single- edged razor blades. No more tools than this are required for planked hulls, although a marking gauge is handy if you are used to using one, and one or two files, and even a rasp, may save a lot of glass-papering. Carved hulls get a bit more towards the real carpentry outfit, and besides the above list it is useful to have: (13) Assorted chisels. (14) Assorted gouges—two or three different sizes are enough. (15) Spoon gouge, about 2 in. (16) Carpenter’s brace and assorted bits, especially a 1 in. size. (17) Calipers. (18) Spokeshave. For large models, a bow-saw and a jack-plane are helpful, but most builders will be able to assess their requirements when studying plans for the proposed model. A useful tool is an Abrafile, which will cut in any direction, and is Tools and Materials used mounted in a hacksaw frame. Other handy gadgets can be made in the workshop; one example is the simple cramp in Fig. 6. lengths of This is made up from two studding (screwed rod) to which are fitted two strips of wood adjusted up and down by nuts, preferably wing-nuts. Several of these cramps will be needed for a bread-and-butter hull. Needless to say, all pins, nails, or screws which structure will remain must be part rustless; of the brass is the normal material for these, though some very fine pins are made only in copper. The most useful type of brass pin is known as a “gimp” pin, and is available in sizes from 4 in. up. It has a flat head of nearly 7; in. diameter, and is thus not so prone to pulling through as brass veneer or panel pins. Screws used are normally those with countersunk heads, and when a screw is driven in, it pays to follow the correct method by drilling a clearance hole for the shank and a thread hole to provide adequate bite for the thread without the risk of splitting the work. A wide variety of glues now exists, and for boat-building there are several specialised products. The first essential is insolubility in water, which rules out such things as Scotch or other animal glues. Some cellulose cements are excellent, especially for work with balsa; harder woods need the slow-drying cements such as “Britfix” or “Durofix”. Unquestionably the best results are obtained with the comparatively recent resin glues. Some of these (Aerolite, Beetle, etc.), are two-part mixes—the resin is applied hardener to mences to brought available to the cure surface other. The when together, for one the but a positioning and glue com- surfaces short time the a joint are is ac- curately. Setting time is affected by temperature, but on average is in the order of 4-6 hours. One resin glue (Cascamite One-Shot) is sold in powder form, ready-mixed and requiring only the addition of water to be ready to use. All these glues are completely water- and heat-proof when set, and they all have the advantage of being gap-filling. This means that when two slightly irregular surfaces are glued, no air-space will remain, since any discrepancies will be filled by the glue. Although the advantages of this are apparent, and the strength of resin glues is enormous, it should not be made an excuse for sloppy workmanship—a top-line boat calls for complete accuracy from start to finish. Only best quality paints and varnishes should be used if a reasonable finish and life expectancy is required. A few cop- pers saved here can spoil the best model, and this includes brushes too. There are several good paints suitable for the purpose, but if possible marine paints should be used. Cellulose is not really suitable, since it tends to sit on the surface and although hard is prone to abrade, or, if water does find its way behind it, blister off. Lead paints are good if an annual re-paint is envisaged, but for general ease of working, good finish, and excellent life, modern syn- thetics are to be preferred. It is a little invidious to single out one of several good products for special mention, but because of its availability amywhere a recommendation can be made—when in doubt use “Valspar”. A later chapter deals with painting and gives full _information on this subject. Finally, to the all-important subject of timber. Builders of hard chine or diagonal-planked hulls are fortunate, for the most reliable timber of all is resinbonded birch ply, and it is readily avail- able in all sizes from x in. up. Occasionally, this may only be found in metric sizes, but the range of sizes is virtually identical and it is close enough to work on the basis of 3 mm. = 4 in. Where timber is required in plank FIG. 5 (above) shows the normal tools required Carved hulls are easier with for a simple boat. the addition of the extra tools illustrated below. 12 BOAT MODELLING 316” SCREWED ROD WING NUT ‘WASHER TIMBER BATTENS FIG. 6.—Cramp for bread and butter hulls. form, the position is by no means so happy. You may be lucky in finding a local yard able to supply suitable wood, but nowadays timber is very frequently kiln-dried, and in nine cases out of ten what may look to be excellent material for the job will eventually let you down. For bread-and-butter hulls the amount of “movement” (from drying out or from residual stresses produced by kiln- drying) is not likely to be serious, but for a planked hull the results can be disastrous. If you cannot buy guaranteed timber locally, send away to one of the model suppliers who can make a special selection through a_ timber importer; it may cost you a shilling or two more, but is long run. well worth it in the An alternative and possibly even better scheme is to have a look round salerooms and so on, for an old piece of furniture or a door which you can have cut at a sawyers. Timber obtained from such a source is often ideal for planking and laminated keels (2 in. is the normal maximum width for such items). The timbers best suited to model work are Douglas Fir, Silver Spruce, Yellow Pine, Red Cedar, Hickory, Maple, African Whitewood, and, of course, Mahogany (preferably American). Of these, cedar, yellow pine and mahogany are outstand- ing, and these woods can occasionally be found at yards dealing in ‘“reconditioned” timber. The most easily available “new” timber, not in the foregoing list, is Obeche (sometimes “obechi”), and if thoroughly dried, etc., this is quite suitable for bread-and-butter hulls, It has the added advantages of being easy to work, and, in normal cases, light in weight, so that a hull need not be carved out quite as thin as is sometimes necessary. Boat-building sizes differ from normal timber sizes for prepared (planed all round) wood. Customarily 1 in. x 2 in. timber refers to the ‘‘sawn” size, and the dimensions are nominal for planed material, which should be & in. undersize, ie. § in. x 1% in. in this example. Sizes given in boat-building are finished sizes, ie. actual sizes after planing. This is important, particularly when working to a lines drawing for bread-and-butter construction, so if you are having tim- ber sawn and prepared for you, be very specific. Many experts have their planks left wy in. oversize and plane down to exact size by hand. To ensure constant thickness over several planks, ask for them to be fed through a thicknesser rather than processed on an overhand planer. In the foregoing, we have assumed average facilities for intending builders. Obviously, a bench and a carpenter’s vice are assets, and some modellers may have power tools at their disposal. How- ever, there is no need to be discouraged if your equipment is limited—a good many championship models have been built on no kitchen table! Gy more than the humble 13 Hard Chapter Three Chine Hulls HARD chine hull is one in which the sides and bottom join to produce an angle, rather than merging gently from one to the other in a curve. The continuous angle, running from near the bow to the stern, is the chine line, and “hard” in this sense is an old shipwright’s expression which, for definitive purposes, can be taken as “acute”. Hard chine hulls are also known as “sharpies” or, simply, “chine boats”. The beauty of the hard chine is its extreme simplicity and speed in construction, coupled with a smaller outlay in ~money and skill. Little use of the idea is made in the full-size industry for boats of over 120 ft. or so in length (although one enterprising firm is now with craft flat-bottomed producing “sharp corners”) since there are certain disadvantages in stability and strength/ weight ratio in really big sizes ; however, for modelling the advantages far outweigh any disadvantages. When a boat is placed in the water, it will displace a volume of water corresponding to its total weight (remember Archimedes?). In actual fact, and as a point of interest, 1.8 cu. in. of water weighs one ounce, so that for example a 5 lb. boat will displace 80 x 1.8 or 144 cu. in. of water. Now, this water is continually displaced as the boat moves along, even at maximum normal speed. If, however, the boat is overdriven, i.e. more power is applied than is needed to maintain maximum normal speed, the boat, by virtue of its shape (without g0FIG. typical 7 section. hard contrasts a more (left) chine FIG. a shows flat 8 curved a cross- (right) run with profile. ing into a lot of theory) will tend to rise out of the water and begin to “plane”, that is, sit on its stern with its bow out of the water. Part of the boat’s weight is transferred to the air and the harder the boat is driven the greater is the proportion of weight transferred. The maximum speed of the boat in this condition is considerably higher, of course. Now, a boat deliberately designed to achieve high speeds above any other considerations, must be designed to plane, and a planing boat requires light weight, a flat run (Fig. 8) and a relatively broad transom or stern end, since this is where it will be chiefly supported by the water at speed. The hard chine hull is ideal for these conditions, which is why air/sea rescue launches, motor torpedo boats, and other fast craft employ this system. The disadvantages of the hard chine are more apparent in sailing craft. Given sufficient wind, yachts will plane on the run, but working across or into the wind (reaching or beating) calls for hull characteristics in which the chine hull does not noticeably shine; chief among these is the necessity to sail at a slight heel (the “sailing angle”) and chine boats prefer to be sailed upright. Even so, the principle reason for the absence of hard chine hulls in full-size sailing is that the rules frequently preclude them; there are, of course. special classes (e.g. “Star” 14 BOAT MODELLING FIG. A 10 (right): typical jig keel. and “Cadet”) which are for chine boats only. On the model side, the windward work of sharpies puts them slightly at a disadvantage, although such boats have finished in the top half-dozen in more than one national competition. It will thus be seen that the hard chine is excellent for power boats, where constant power is available irrespective of the wind, but has limitations for sail- ing craft. For a beginner, the simplicity of construction frequently outweighs any in performance, so_ that limitations whether power or sail is preferred, a boat with this type of hull should be first choice for a novice. Construction The basic hull of a sharpie at its simplest consists of five longitudinal members—a central keel, two chines (sometimes called “chine stringer” or “shelf’’) and two inwales (Fig 9) to form the remaining two corners of a pentagon —plus a number of lateral members (“frames” or ‘“bulkheads’’) and a stem and stern. There are two methods of producing this basic assembly (a) by making the keel member a jig to which the bulkheads are fitted, or (b) by erecting the bulkheads in a separate jig (upside down), and adding the keel, chines, and inwales, removing the jig at a later stage in the building schedule. Which of these two basic methods is adopted depends on whether ‘the bulkheads are to remain a permanent part of the finished hull. The average power boat is built up as a complete structure, with all the components added during building remaining part of the finished model. Usually this means a fairly generous keel member upon which the bulkheads can be fitted See and aligned positively, but occasionally “ege-box” construction is used (Fig. 12). In this, two longitudinal built-in jigs receive the bulkheads, each item being slotted so that positive alignment is assured. Light inwales, chines, and keel are added before planking or skinning. An advantage of this system is that an accurate hull can be built by anyone able to wield a saw reasonably well. With a single keel care must be taken when fitting inwales and chines to avoid stresses likely to lead to an asymmetric hull, and it is best to fit these members in their respective pairs. ne FIG. 13.—Laminated keel/stem structure. Breaking the assembly into detail, let us examine the most popular form of power boat hull. The first item is the keel, and the modern scheme is to cut this from ply which, needless to say, has to be of the waterproof, resin-bonded type. At one time the keel and stem were fashioned in one piece from a grown crook, but with ply this is unnecessary, since the stem can be cut as part of the keel. Occasionally a laminated keel/stem is used, particularly where a gentle curve exists at the bow, and this is made from thin strips glued FIG. 11.—Building In a separate jig. 15 HARD CHINE HULLS FIG. 12.—’‘Eggbox”’ construction, together under pressure (see Fig. 13). Another method is to cut the stem and keel from timber of 8 in. thickness or more, making a glued joint reinforced by brass pins or screws and a “knee” cut from the same timber (Fig. 14). With the normal single-screw boat, the propeller shaft must pass through the keel. There are two types of shaft, that which is enclosed in a tube for the whole of its length, and that which runs “in the open” and is provided only with a short “stuffing box” to provide a bearing and a seal where it enters the hull. The tube type has a bush at each end FIG. 14, 3 only, so that the diameter of the tube is rather greater than the shaft diameter; as an example, a +; im shaft is normally found in a @ in. o.d. tube. Exposed shafts are usually fitted to racing de- signs or very fast boats where a_univer- sal joint is required, but for the average boat the full-length satisfactory. tube is and width for the shaft, and the two parts pinned accurately in place over the plan One block is now glued in place and left to dry thoroughly, following which the assembly may be lifted and the second block glued in place and pinned or screwed through to the other. This is a much more accurate system than endeavouring to drill or burn a hole through after assembly. The tunnel in the blocks may be drilled with the channel in the ply as a guide, but it is better to chisel and file each block before gluing in place. A close fit is not absolutely essential, since any gaps will later be filled with paint-soaked cotton waste rammed in tightly. When a thick keel is used and it is necessary to drill a shaft tunnel (an operation usually performed at a late stage of assembly) much trouble can be avoided by making a simple jig as in Fig. 16. The length of hole to be drilled TEMPLATE quite The problem of passing a & in. tube through a keel which may be only 4 in. thick is overcome by fitting blocks on either side (Fig. 15). A strip is cut out of the keel at exactly the right angle | | PARALLEL FIG. 16. 16 BOAT MODELLING chines may be positioned. There is frequently a sharp curve towards the bow, is usually considerably greater than that of a standard drill, and unless a special long-shanked auger bit is purchased it is advisable to burn a pilot hole through with a red-hot wire (about 12 s.w.g. is adequate). This hole can then be followed from both ends and rat-tail file used to finish the tunnel off. It is usual for the keel assembly to project slightly beneath the completed boat, i.e. the planking or bottom skin butts against the keel side. To assist in making a good joint, some provision is usually made for seating the skin, and although the keel can be rebated for this, it is much simpler to glue and pin a stringer in place on each side of the keel before assembly. These need only be % in. square. On some designs the bottom skin panels “overlap” the keel, butting against each other to form a smooth V along the whole length ; this merely entails chamfering of the actual keel to suit (Fig. 17). The bulkheads or frames are glued in place on the keel assembly (still considering the average model) and the joints may be halved to ensure correct positioning. Where a_ bulkhead is simply notched to receive the keel, skewed pins can be driven through to strengthen the joint. When all bulkheads and transom are in position and dry, the inwales and FIG. 18.—Scarf jointing. particularly with the inwales, and this is sometimes sawn to shape from flat material. Where a single strip is used, it may be necessary to steam or soak the curve in, and in this case it is advisable to pin or strap the strips in place temporarily and allow them to dry before gluing and pinning permanently. Wetting tends to swell the wood and on drying a contraction of 4 in. is quite to be expected in a 3 ft. length; this is enough to pull the structure severely out of shape. The best method is undoubtedly to laminate chines and inwales from two or three more easily bent strips, gluing along the whole length. This also reduces splitting if pins are driven through when attaching the skin. When the glue is dry, plane off the strips to their correct sections. If sufficiently long strips of material are not available, scarf two or more strips together, the ideal joint line extending over a distance of eight times the width of the material (Fig. 18). Place such joints at points of little stress, i.e. where the curve is slight. When skinned, no difference in strength will be noticeable. The entire framework should now be examined carefully for truth. Sight along centre lines for symmetry, above and below, and check that no twist has crept in. Any internal details such as motor mounts, etc., before the hull is that must planked be fitted should be attended to before proceeding further. It is customary to “plank”, “skin”, or FIG. 20.— Bow blocks. Bass of models raced either nationally or interNationally, the A class. The two in the photo- ee \ The yachts on the right belong to the largest graph are being released for a run and hence have spinnakers rigged. Displacement of such boats averages 56 |b. On the left are two 10-rater yachts about to commence a run with spinnakers drawing nicely. The boat nearer the camera is very unusual in that it is a hard chine design, rare in this class. The average 10-rater dis- placement is about 28 Ib. The most popular class of yacht is now the 50 in. Marblehead class, two examples of which are seen on the right drawing away from their skippers’ hands on a beat to windward. mally about 22 lb. displacement, Nor- this type of boat is relatively easy to transport. ag SS The smallest M.Y.A. class is the 36 in Restricted, in which boats are limited to a displacement of 12 lb. maximum. The two on the left are taking part in a national championship; such championships are organised every year for all the recognised yacht classes. PLATE 1. os es Bae Pee sti Above and on the right is a very simple 23 c.c. three point hydroplane. This does not conform with any M.P.B.A. class, but is of a size popular for sport running, and is illustrated because it shows the bare essentials for this type of model. Below is a baby Jetex powered hydroplane, ie which demonstrates the accessibility of the power unit and the simple construction typical of this type of model. Above is a steering which launch, no makes pretensions to any scale appearance. Power for-this particu- lar 48 in. model is a petrol o.h.v. 10 c.c. engine, and the displacement is 12 lb. fine a Left, ex- diagonal of ample planking for a hard chine photo- hull, graphed painting. structure before The superof this steam particular launch is fabricated entirely from dural, a job rather beyond the but scope. skilled workers. The shown launch on the right is steam nearing the end of its 80 yard course to wets, The such as two runs score an rules inner for on the steering tar- contests this may take the better as the final score, or of the Aggregate score of two or more runs. PLATE 2, of any metal HARD CHINE HULLS 17 “cover” the underside of the hull first, and the usual method is to cut thick brown paper or thin card templates to the approximate shape. The inner (garboard) edge is all that need be accurately fitted, and an overlap of about 2 in. is all that need be left on the other edges. After the template is satisfactory, cut the ply and fit the garboard edge accurately by taking a fine shaving or two off with the plane to produce the slight chamfer necessary. Glue all the contacting surfaces, position the ply, and drive in pins, either as permanent fixtures, or to provide temporary pressure while the glue dries. In the latter case, hardened steel dressmakers’ pins, pressed in at an angle with pliers, are ideal. When the glue is thoroughly dry the FIG. 22.—Diagonal planking. times the extreme bow is built up from vertical strips of timber around 3 in. thick, the flare being carved in when the glue is dry. SS FIG. 21. Zz SK . — = surplus material can be trimmed off with a sharp knife and the edges planed flush. The side skins can now be attached, allowing a small overlap al! round, trimmed and planed off whea Some scale models may have flare running along the entire hull, sides and bottom. In such a case diagonal planking is frequently employed; this is a simple method and, if double diagonal planking is used, results in a remarkably strong hull. For most models the ply or timber can be cut into long strips 1 in. wide; the end of the strip is laid in place somewhere amidships, at an angle of 45° to the fore-and-aft line, marked off, and cut to length. A small overlap can remain if required. This strip is now glued and pinned in place (a sheer stringer running the length of the boat dry. Fitting the ply skins is not difficult except where sharp changes of angle are required or excessive sheer (concavity of the surface) occurs. In the former case the only really sharp change is at the boat’s forefoot, and it is customary to fit solid blocks at this point (Fig. 20) or to plank the extreme bow with narrow vertical strips. Flare can usually be induced into ply by steaming or slight damping, or even leaving the cut sheet in a tray of wet sawdust for a few hours. In extreme cases narrow vertical strips can be used, and a sheer stringer let into the bulkheads midway between inwale and chine facilitates this (Fig. 21). Some- FIG. 23.—Double diagonal planking. 18 BOAT MODELLING The is desirable) and another strip laid up to it, cut, fitted, and so on, until the entire surface is planked. Double planking means laying on a second set of planks at right angles to the first. This system, using sy in. (.8 mm.) ply for each “layer”, is excellent for strong, light hulls up to 48 in. in length. Before decking, the interior of the hull requires painting (see Chap. IX). After painting and completion of internal detail, the deck, suitably cut for hatches, etc., can be glued and pinned in place, completing the basic hull. A hard chine hull can, of course, be built without permanent bulkheads, and yachts with such hulls are usually built in this fashion. The “shadows” employed are more or less bulkheads which are later removed, and the essential differ- ence in that the hull is built upside down on a jig in much the same manner as a planked hull. Reference to the next chapter will fill in the details following outline procedure. of the Gy shadows are cut with sufficient material left above the inwale line to bring their top edges to a straight line. All required notches are cut for keel, chines, and inwales, and the shadows, stem, and transom are then erected on a jig board at their correct stations. The fore and aft members are added and lightly pinned in place (they can, of course, be glued to stem and transom) and the resulting frame skinned as previously detailed. Care must be taken to glue the skin only to the permanent structure. When dry, a rigid assembly remains, which can be cleaned up exter- nally with complete safety. The assembly is then removed from the jig and the shadows twisted out. Timbering, deck beams, etc., can be added as each shadow is removed to reduce any chance of the hull springing out of shape. The big advantages of hard chine hulls are that they are simple and quick to build, light in weight, and, of course, they offer little difficulty in timber supplies. Ply is the main material, and is reasonably easy to buy anywhere. The chines, etc., can be made from any longgrained wood, and spruce should be available in any respectable model or handicraft shop. Failing this, obeche can be used if no better choice lies to hand; some of the exotic timbers imported—sanga, meranti, quaraba, etc., are perfectly suitable for such purposes, if thoroughly dry. ROUND BILGE HULLS Chapter Four OST full-size craft have “round bilge” hulls, the “bilge” being the part of the hull between the ‘‘floor” and the “side”. When the floor curves gently into the side the hull is of the round bilge type; softening the turn of the bilge means making the curve flatter, and hardening the turn is the reverse, terminating, of course, in the “hard chine” when a definite chine or corner exists. A very high proportion of model boats do, of course, follow full-size prototypes to a greater or lesser extent, which means that the round-bilge hull is common in the model world. Most model yachts employ a rounded hull, too, since there are hydrodynamic advantages in this shape. At one time it was normal to carve such a hull out of one solid lump of timber, and for small hulls this may still be done (Fig. 26 gives the easiest system). However, the two main systems used nowadays are much easier and more economical; these are the bread-and-butter and rib-and-plank methods. Bread and Butter In this system the bread is the timber and the butter the glue used to bond the planks together. There are two separate methods, bread and _ buttering on the waterlines, and bread and buttering on the buttocks. To explain these we must look at a typical lines drawings 19 Round Bilge Hulls of a hull as prepared by a naval architect ; a small scale reproduction is shown in Fig. 27. Looking at the profile of the hull, it will be seen that the shape is divided into equal “slices” by horizontal lines. These are the waterlines, and they are shown in full on the plan view of the hull just below. If timber of the same thickness as the “slices” is cut into a number of planks, each shaped to one of the waterlines, an embryo hull is immediately achieved. It will be apparent that all but the bottom plank can have much of the centre removed before assembly; an accurate assessment of the required inner line can be made by sketching the structure and wall thickness over the body plan (the third part of the drawing) as in Fig. 29. If this is done on each section shown on the body plan, a series of points can be marked on the planks which when connected will give an inner line to saw to. Lower planks can frequently be cut from the inner parts of the upper planks to economise on materials. The second method also uses the lines given on the drawing, in this case the parallel fore-and-aft lines dividing the plan view. These buttock lines are shown in full as the curved lines on the profile, and the planks will, of course, be vertical and in pairs. The same system of determining how much may be safely cut out can be followed. This FIG. 25 (left) section. carving. shows a FIG. 26 (above) typical round-bilge crosspreparing a block for BOAT MODELLING 20 method has achieved considerable popularity in recent years, particularly for racing yachts. One special advantage is that it is easy to check that both sides are absolutely identical, since the joint ; lines can be used to ensure symmetry this is of paramount importance. Whichever method is followed, the procedure is identical. After sawing the planks to shape, they must be thoroughA ly glued together under pressure. high-quality glue is essential, as is accuracy in line-up. Several cramps will be needed to provide an even pressure, and these can be made very simply, as detailed in Chap. II. Plate III shows a hull glued up under pressure. While the glue is drying, a set of templates should be prepared by tracing off the body plan on to thin ply, stiff card, or even thin metal. The outside of the hull is then carved to approximate shape, using chisel, plane, spokeshave, rasp, etc., and making rough checks with the templates. When the final shape is emerging, accurate pencil lines should be drawn at the template stations to assist the work. Always use the cutting tools “downhill” on the grain, and never take off huge cuts. Finish this stage with coarse glasspaper, since small scars are likely to be sustained during hollowing the interior and these will be removed in the final glasspapering. The interior is hollowed by using a brace and bit to drill closely-spaced holes where much material has to be removed. An odd length of tube slipped over the bit shank and taped to the chuck can be used as a depth gauge. Typicat_cposs SECTION OF HULL WIDTH FIG. 29.—Horizontal laminations. FOR INSIDE OF LAYER FIG. 30.—Vertical faminations. 21 ROUND BILGE HULLS FIG. 28.—Bread and buttering 374″ DIA HOLES FOR on KEEL BOLTS. JOINT HERE LEFT UNGLUED TO FORM DETACHABLE KEEL a om i—t = 1 2 4 pi 4 Vidw OF GLWED UP HULL BEFORE CARVING. The remaining material is pared away with a gouge, again taking light cuts down the grain. It is well worth making a pair of double-ended calipers (Fig. 32) for checking wall thickness as work proceeds. The interior should be finished smooth with successive grades of glasspaper when the designer’s specified hull waterlines. may be a flat plank of 1 in. x 4 in. or so, slight- ly longer than the hull to be built. Occasionally a second piece of timber is screwed beneath the first to form a BENCH – ee the TOP. “T”, which ensures that the first board cannot assume a curve during building. Shadows, usually of 4 in. ply, are now cut and fitted to the jig. Each shadow weight is within reach. Deck-beams and other reinforcements should be added (Fig. 35) and the ex- terior polished up with fine glasspaper before proceeding with the initial painting stages. FIG, 31.—Use of templates. Rib and Plank This system offers a rather lighter hull and is thus possibly more frequently found among model yachts than power boats. Material requirements are a little more stringent, since a finished hull can more easily twist or “starve” out of shape, but less heavy work is required to build a hull by this method. The following description applies to a yacht hull, but may equally be applied to other craft. The first requirement is a jig, which FIG. 33.—Holding a hull for outside carving. is traced off a body section on the body plan, but since these sections show the outside line of the finished hull, allowance must be made far the thickness of the planking and the ribs. Where the shadows will remain as bulkheads in the finished hull, only the planking thickThe ness is allowed for, of course. shadows are extended at the top so that the extended tops all fall on a straight line (Fig. 36), and they are secured upside down on the jig either by cutting notches in the jig and pinning them in, or by screwing a 4 in. square fillet to the top of each and screwing into each fillet from the underside of the jig (Fig. 37). Notches for keel and inwales must FIG. 34.—Holding a hull for inside carving. be provided in the shadows, and they must be very accurately positioned on the jig. The keel, stem, and sternpost assembly (the backbone) is next assembled uirectly over the plan; in the case of a yacht FIG. 32.—Double-ended calipers. this is normally one smooth sweep of timber, and is best laminated from several strips of 4 in. material (Fig. 38), the width corresponding to the plank width at the midsection, ic. 3 in. for A hulls. BOAT MODELLING 22 FIG. 35.—Deck Positions on a model. FIG. beam small ow. Jib rack support. vane support. f in. for 10 Raters and Marbleheads, and 3 in. for 36R models, etc. When thoroughly dry, the backbone is dropped in place in the shadows, and the inwales similarly positioned and glued to the porary pins can be tapped in to hold them to the curve of the shadows. Check alignment by laying a strip of planking in place. h! t Hl RU! supe iy FIG, 37. i Ls extended ‘ owe | L omer – a ——$ Note shad- top and plank spacing out. marked ready B, D, E, F. Deck Beams. C. Mast slide supports. G. Rudder trunk and/or A, 36.—Full oe stem and transom, either direct, or by means of the breasthook, etc. Blocks, suitably rebated, are usually employed at the extreme bow and stern (Fig. 39). Usually 7; in. ply is used for the ribs. and this is cut into 3 in. strips fitting round each shadow from the keel to the inwale. A little additional strength may be gained by jointing the ribs into the backbone and inwales, but the most important thing is to see that the ribs are flush with the other members. Tem- foal t eb) sous T T JoECK Une tracing [or THE PROFILE FIG. 38.—Backbones may be laminated in jigs of small wood blocks, or sawn from made up the solid. The planks are normally cut from % in. material—slightly thicker for the bigger classes. The planking must be set out on the body plan by stepping off the largest section to the required plank width (see above) and diagonalising as in Fig. 41. Note that most of LZ FIG, 40.—Fitting . FIG. 39.—Stem block. km of rib. the planks terminate on the backbone and do not run from end to end. The approximate plank width at each section can be taken off this “planking plan”. Mark out two sheer planks (one left and one right if your material is planed on one face only) leaving the top edge 23 ROUND BILGE HULLS “point” thus formed is planed off to 3-8 in. flat and a strip of wood fastened = FAG, 41.—Body planking plan. and round gi 44 an ay ono t BT APEROR DATUM ? , straight; make sure that the marks made for the widths at the section stations join in a smooth curve. Cut and plane the curved edge, square to the face, and glue in place (planed face in if not planed both sides). Normally the deck will be screwed on top of the planking, but if you wish to let it in allowance must be made for this. The planks may be pinned in place (some experts use bootmaker’s tingles for this), ‘ <—*7* “DATUM i STRIP SAME THICKNESS AS PLANKING | REBATE FORMED BY STRIP, FOR PLANKING KEEL OR BACKBONE » PLANKING IN PROGRESS FIG, 43.—Forming a rebate for the after planks. cleaned up. deck. /MALTERNATE PLANKS SMOVERLAPPED AT BOW is dry. The second pair of planks is now prepared in exactly the same way, except that the top (straight) edges will require the faintest of bevels to fit snugly. Continue in this way. When the after ends of the planks approach the backbone, glue and pin a strip of planking over about section. The garboard true surface. piece is cut from a single block, and is best fitted by drill- the pins being withdrawn when the glue the backbone, correct ing the keel bolt holes through it and the backbone, and bolting together while the glue dries. The piece is then faired into the body and the planking can be FIG, 42.— Inset or overlapped to This “locks” the planks and moreover prevents them splitting if the boat has the misfortune to ride over a hard obstacle. When planking is completed the hull must be planed off to receive the garboard piece (Fig. 45) and great care must be exercised to ensure a perfectly icy ry planed 3 in. narrower, from the transom to the after end of the deadwood, to form a rebate to re- ceive the plank ends. The forward plank ends are alternately overlapped (Fig. 44) over the backbone, and when all the planking is completed, the PLANED OFF. STRIP ADDED AND SHAPED 24 BOAT MODELLING itself is cut and fitted in the slot; for additional strength it may run right through to deck level (Fig. 47). Check that the alignment is perfect before gluing permanently in place. Now remove the building jig, leaving the shadows in place, and bolt the hull to the bench or to a strip of timber held in a vice Knock or twist out the shadows, working from ends to middle, and clean up the inside of the hull shell. Any further internal reinforcement must now be added; this is usually limited to load-spreading members designed to dis- FIG. 45.—Planing off for the garboard piece. Scrape off any surplus glue and withdraw all pins. Run a plane lightly over the “corners”, and glasspaper with a coarse paper in all directions. Proceed with progressively finer grades of paper, lightly damping the hull to raise softer fibres, until a reasonable surface exists. Before moving the hull mark out the slot for the skeg and drill and chisel right through the backbone. The skeg FIG, 47.—Skeg and other aft details. tribute the stresses of the heavy lead keel (Fig. 48). A handle is usually incorporated for carrying the hull (Fig. 49). At this stage, too, the first coat or two of the interior varnish may be brushed on (see Chap. IX), — fi FIG. 48.—Athwartship load-spreader to take side strains of lead keel. FIG, 46.—Chiselling the skeg slot. The next job is to fit the deck beams. These are cut to length and planed to correct camber (if a cambered deck is employed) from similar material to that used for the inwales. The beams are then halved into the inwales and fitted flush (Fig. 50). These beams are positioned to stiffen the deck and also to provide anchorages for various deck fittings. Fig. 35 shows a typical lay-out. Ply is normally employed for the deck, and this is cut to shape and cleaned up, . ROUND BILGE HULLS {1 KEEL KEELSON 25 1) KEEL 1! —_ pour + FIG. 49.—Internal carrying handle. FIG, 50.—Deck beam/inwale jointing. but not fitted until the interior is fully which, when cast and cleaned up, is be cut and the cover fitted; this is located over the keel fixing bolts and the aperture should be large enough to the fin (the deadwood) in the manner varnished, etc. The hatch, however, may bolted through the remaining portion of described in Chap. VIII. about hatch, tightly be of 3 in. larger all round than the to which is cemented a plug fitting the hole; this may also timber but a better job can be Many types of hull can be built on the rib and plank system, following the general principles outlined above. Most will be simpler; for example, a small trawler hull would use a block stem and counter with planking between, and would require no garboard piece or skeg, The which wood. cut to remaining job is the is shaped from one The entire fin is shaped provide the pattern for fin keel, block of and later the lead, occur, planking can be difficult, so that the drawings for a proposed model should be carefully considered before deciding on rib and plank construction. admit a hand. The hatch cover is normally a rectangle of mahogany, etc., made by using sheet cork. etc: Where sharp changes of curvature 26 BOAT MODELLING Chapter Five ib hearsee are several other systems for building which apply to specific types of hull or to the working facilities available. Many of them are variants or combinations of methods already described, but one or two are completely different. *Two-shelf’? Chine Hulls It will be obvious that a hard-chine hull is five-sided, the widest “side” being the deck. If we make the deck a primary structural member in the form of a complete shelf sawn to plan-shape, and make the chines in the same way, we have only to add a keelson or keel assembly to provide the “fifth corner” (Fig. 51). Lorelei and Water Bug (Plate TI) are built on this system, which was first popularised by the author. Its chief advantages are the ease with which a symmetrical hull is produced, the positive fixing for the ply skins, and the small amount necessary. the of internal structure Camber may be planed into deck, and if pliant timber is used, deck sheer and chine curve can be incorporated by judiciously placed bulkheads and diagonal bracing (Fig. 52). Naturally, the system is not quite scale boat-building, and has its limitations, but for ease of building and overall strength it has much to commend it. Other Types of Construction Composite Hulls Quite a number of full-size ship types lend themselves to the simplified construction shown in Fig. 53, common examples being destroyers and oil tankers. The bow and the stern are the only parts deviating from a squarish cross-section, so these are built up on the bread and butter principle, with the midships portion employing only three planks for the bottom and sides. The thickness of these planks allows for the hull section to be carved in, but when thin planks are used a fillet can be fitted into the corner to preserve strength (Fig. 54). Thick-bottom Hulls In some cases of boats similar to the foregoing, it is possible to use one thick plank for the hull bottom and erect ply sides for most of the rest of the hull. The sides normally need to terminate on a bulkhead towards the stern, and the stern itself is then planked on a light frame or even bread-and-buttered. The round of the bilge will determine the thickness of the bottom plank (Fig. 54). Diagonalled Bilge Hulls The cribed diagonal-planking in Chapter II, is system excellent desfor round bilge hulls, with or without permanent bulkheads. The one difference in setting up for planking is that stringers are necessary in addition to ribs. These must be flush with the ribs and spaced about 2 in. apart, running from the extreme bow to the stern. The planks are laid on in exactly the same manner as for a chine hull, and joined to the backbone in the same way as 27 OTHER TYPES OF CONSTRUCTION The second layer can normal planks. be laid on fore and aft instead of diagon- ally, if preferred, with no measurable When effect on the ultimate strength. applying diagonals, the width is governed by the amount of curvature, ie, the planks will be narrower at the ends than the centre with an average hull. A trial strip will quickly determine whether the width is too great. Gum-Strip Hulls The enormous strength of laminated gum-strip paper is not generally realised. If you require to be convinced, soak a length of good quality gummed brown paper strip and wind it carefully round a broom-handle (over an ordinary sheet of paper so that it will slide off) until it approaches +, in. thick. Allow to dry thoroughly or bake the tube in a cool oven for an hour, and then try to collapse it. It can be done, of course, but the force required is quite astonishing. LIL FIG. 54.—Corner fillets and thick hull bottoms. Hulls can be built of this material quite easily and with very satisfactory results. A very light armature is neces- sary, and the best way is to cut ply bulkheads, notch them to receive y_ sq. stringers, and set them up in a jig. The stringers need only be 4 in. balsa, but they must be spaced no more than 4 in. A heavier inapart on sharp curves. FIG. 53. shellac. Varnishing or painting thus has a hard base and is carried out normally. A hull built in this way is a fraction heavier than a wood-planked hull, but a first-class job in every respect. Papier Mache Hulls This method is rather a misnomer, since the paper used is not pulped com- pletely. Frankly, it is an evil-smelling process offering little advantage over the previous system except that it is very cheap. Tear a large quantity of old newspapers into squares of 3 in. or 4 in., and drop them in a bucket of water into which has been dissolved a packet of glue size. They should soak for a wale is desirable, since a ply deck will be screwed to this. Thoroughly soak the strip and lay it on round the hull first, then diagonally each way, then fore and aft. Repeat until a good thickness is built up—-+, in. is adequate for ,.most purposes. Only short lengths need be used, and care should be taken to avoid too many air bubbles. When completely dry, rub the outside down and apply one or two coats of shellac. Rub down again, and shellac five or six times more, rubbing down between each coat. The inside also requires several coats of FIG. 55.—Armature for gum-strip hull. 28 BOAT MODELLING day or so before being used. An armature similar to that described above is needed, but the stringers may be spaced further apart. Lay the squares of paper in place on the frame until three or four layers have been built up, then allow to dry off slightly. Brush thin glue over (“toffee” glue will do) and add a couple of layers, brush on more glue, add layers, etc., until a thickness of yy so has been reached. above. Strawboard Strawboard in. or Finish exactly as a low-grade type of card, usually grey or fawn in colour, used for packing, etc. Hulls can be built from this material, using it in exactly the same way as timber, and finishing with the shellac process described for the two previous methods. It is par- ticularly suited to diagonal planking and offers the advantages of exceptionally low cost and easy availability of the material. Hulls built of strawboard demand patient workmanship to achieve first-class results, but are extremely strong and seaworthy when finished. Working is simplified by the flexibility of the material when damped. Clincher Clincher, Built or Hulls clinker, building, is a system of producing a hull with no in- ternal framework, and incorporates overlapping planks (Fig. 56). Most ordinary rowing boats, dinghies, lifeboats, etc., are built in this way. Procedure is much the same as for normal planked hulls, except that sufficient width must be al- lowed in each plank for the overlap, and planking must start at the garboard, ie., next to the keel. In full-size practice the planks are often merely pinned but in models it is usual to glue the overlap as well as pinning it. Ply is usually used for planks, since the pins are close to the edge and splitting is frequent with plain timber. At the bow and stern, the top of each plank is chiselled off to a feather-edge for an inch or-two; this allows the next plank to seat down to a nice smooth finish. The pins, projecting inside, are snipped off after completing the planking, and clinched over inside. Timbers are Hulls is together, now added (Fig. 56) by pinning through from outside and clinching over. Longitudinal stringers (risers) are added to support thwarts, etc. Few boats greater than 30 ft. or so are built on this system, except for large ships’ lifeboats and whalers, which may be as much as 70 ft. in length. Fabric Hulls Occasionally a very lightweight hull may be required, for example for rubberpowered speed models. This type of hull can be made by building a hard chine frame of as light construction as will do the job, and covering it with silk or nylon The material should be applied by soaking in water, blotting lightly in an old towel, and stretching on the frame using pins and a cellulose cement or thick clear dope. The ad- hesive will “blush” on contact with the wet fabric, but this will disappear when the material is treated with two or three coats of clear dope and a coat or two of banana oil. Alternatively, two or three coats of varnish may be applied. Metal Hulls produce a The production of a metal hull is not difficult provided that the design takes into account the limitations of the material. To arrive at a design and to set of templates, a hull should first be mocked-up in stiff card. Anyone capable of assembling a multipiece metal hull will be experienced enough to know the limitations of his medium (Fig. 57 shows a typical boat FIG, 56. for this type of construction). The beginner is advised to try the two-piece type of hull laid out in Fig. 58. The main section forms the hull itself, and a= Beaveatun= OTHER 29 TYPES OF CONSTRUCTION FIG, 57.—An ‘“‘exploded"’ sketch of a simple all-metal model. HAND RAIL. SLIDING ROOF, ‘CABIN FRONT. MAIN DECK. PORT & STAR'BO SIDE PLATES (CABIN), FOR'ARD BULK'HD. AFT BULK'HO. BOTTOM PLATE. PORT SIDE PLATE (HULL) BTAR'BD —-— TRANSOM TRANSOM PLATE PLATE (CABIN) the application of the resinbonded glass fibre technique. Glass fibre, so treated, is outways, many in standing to regard in particularly strength/weight ratio. A hull of this material is virtually in- is cut from zinc or lead-coated steel of appropriate gauge. One or two wooden formers help to achieve the desired “rolled” shape and these may be per- manently installed with screws or later replaced with metal frames. The second piece is the transom, and the assembly is tacked together with solder and cramps and trued up before the final jOints are made. These are soldered with the aid of a blowlamp, soft iron wire (sz in. or 12 s.w.g.) being laid inside the corners to help form a fillet. Keel, etc., may be soldered in place, but the deck, motor mounting, etc., are best fitted by means of wood blocks secured to the hull by bolts or screws. Glass Fibre Hulls One of the most interesting post-war developments in the model boat world is destructible, and remains constant in shape and weight since it is impervious to heat as well as water, oil, and most other There are two primary substances. methods of using it for a hull: (a) armouring; and (b) moulding. Armouring is fairly self-explanatory, and consists of encasing a hull in the glass and resin which, incidentally, will adhere to almost anything. The model is built in the normal way, except that it is planked in balsa (or carved from balsa) which is considerably easier and faster to work with; furthermore, the surface does not need to be perfect, ie., planks need not meet exactly provided that the gaps do not exceed about 3 in. Now, glass fibre is available made up into broadly three different forms, glass tape, which is finely woven and has little application for our purposes, glass cloth, and chopped strand mat. Glass cloth Ll “| + SIDE PLATES. - 12 OFF Or a (ag —s roy [BOTTOM PLATE , \oe 138 ris laid out for scaling up. Structure is also suitable for an all-pl model if pratarred. THIS PORTION CUT OUT be o1?234 INCHES, Coes nee = | ! = = CABIN PLATES 20°F 2% = rl ys 5 Hts a | |t | de aaa We I = 5 3 Sy oT I above | | sea3)(gys ZT‘UI/’z03B v 0 8 ‘ s :ezu0Ig “HPS npayuo 4tdy xgy“ul “xewg uljoxeg BOAT MODELLING j“eIuTsWa-r}y’‘=UOANdDi|1Y:97euon2®Qpas ®(381153H0)SO‘4I4W09,HaM0s.3eW2qGA0I)33MuV(3nW$oI5w6A31N3(S¥98!15NI) “p(J4uginOa5o1w) ayp“soAieujgnd ‘ 3 s n 8 n y ) ( s S 6 1 Q0S-0SE “w’d-4 ‘4aquia on) (Ss61 HOM LAVS8 partyimdsjo1u0>pe op“ad1usjeyw =3U‘lyjDBNoaxItsOdu’EgA e@A0ylu3p asta ‘Aew) (ss6 ‘4@qua das) (S$61 ( ‘ 4 @ S q u s i a 6 d l ) auAjqipsde Aiquase pJjaeurisy psauesjd YBuidsa a d o5 a d os :*a}zU109§g Buneriqny “41S “31S Buneri gny 2D4WnIsSsteuIlrgd“tip $|20 Bopeusry 7“Buoly B‘uory Og ajod-¢ a ajod-¢ “Dg ajod-¢ “ep | ‘ul ||Hf“ul ““wpur Buoj W ‘ O ‘ T E L “ U w Da“Wda ajod-¢ “Wad :3481aHEZ “UL S“iupy g“xew “Wad Jausew 4Ap9ta3y‘BIOL “a8lOL 381951 SL1-01 Bunesadwo ado5uoqies> Bunesadwo s tag B:“34uL8Iy9H )@alap ST1-O1 $2]0A MA “uy “eyp ¥ ‘uy “tip St cur “tip aag Uld =SONIW3E 8vO-0eo ttol 9S2J0A Ose’ $93]0A TI O1szo Ti1sV3LSaunebso>y 9SIJ0A Ol ze )(sdwy) (Cur’z0 93]0A 9$3]0A HJSX1IIYGMONLA—dNTWVGd =coOz =E01r’0s p‘wru’odj-y +20S’7— 2 gl “Ur S3YNdI4 “Wad Bou “wad “ajDodG-¢ Sa“u”tUylgip sutagd B:“aXUsEelg ¥9*Z0R:“aUsZeyg $2“u473l9H 91 APPENDIX VII—BRITISH ELECTRIC MOTORS vos0’e auaeyqne>uiawab3s-oy “ulda jo Aey Sunesadwo> uoSsktayg oqitd uoqies) Bundspa ro| O“TeULil” $3Pu47r819 ajod-g”3’0 “wdad uXly 2y31ay [|”20 IdO-ure gl78“yBu7laTy xgL F2“4u8L1r9H OZ”20 “‘uXxUlEy x “ u l y EL“4 “Wag ajod-¢ “Wdad Bex] SUES SITES “39S 0703 asudenys -a d os Buridspa ro; a d osy ysaw s eag uljoxed FTX “ul “R:“ausZelg xui gl Ki $920 pajdwig“a@szZouy01g Pgx LHOIFM Ss4teVaDg S3TJ0LA o§ ur ep 8L4VHS pauiwsag S92]0A AL ‘uy 14SV345 ))Cu(rs-dzw0y O9st0’ 6$3104 g$310 QsO3oSd’87|we PtuO] $x “ul FREI a p) (sageys ysiuy BLL 33/04 WldAL s3undi ‘Asenuel) (s et sA‘ayjuIonegiwQ a1qis ay At uy “tip Q3M3IA3Y HOIHM 7Ai“-dans (3unros )‘(sauen1t *(As1ne{i) BE”20 iFXxTE “Sa5n,dry 4asnzIeNutwy, itt 92 BOAT MODELLING Glossary Some of the more common nautical terms, full-size and model. ACTUATOR.—A mechanism for moving controls, etc., set into action by means of radio. . AFT (Abaft, After).—Towards the stern or rear. AIRSCOOP.—A simple type of ventilator for small craft. ALOFT.—Above deck. AMIDSHIP (’midship),—Central. ANODE CURRENT.—An electrical current permanently flowing when a valve is in operation, changed by receipt of radio signal. ATHWARTSHIP.—In the lateral plane. AUDIO TONE.—A means of radio control BOWSPRIT.—A spar projecting forward bow from which headsails are set. BRACE.—A differing frequencies imposed on a carrier wave. leading up from the the yard arms to control the yard position horizontally. BRAIL.—The rope used to assist the furling of a fore and aft sail. BREAD AND BUTTER.—Hull construction a number of planks laminated together. BRIDLE.—A short line attached at two tether a model for running. BRIG.—A_ using line of two masted square-rigged using points to vessel. BRIGANTINE.—A two masted vessel square-rigged on the foremast, and fore and aft rigged on the main, er gears the by mast BAFFLE.—A perforated plate set in the fuel tank, etc., to reduce liquid surge. weight usually in internal solid frame dividing the ship. BACK-LASH.—Taking up of play in back pressure. BACKSTAY.—Line leading down from to brace it from aft. BALLAST.—Extra gmAD.—An the form of BULLSEYE.—A edge, and circular block grooved round its pierced through the centre for ropes. BOL W ORES The sides of the vessel above deck level. BUNT.—The centre of the BUSH.—A metal bearing. square sail. oo added to bring a boat to its correct waterine. BANG-BANG RUDDER.—In radio control a rudder which has only three positions, full left, neutral, or full right. BARBETTE.—Circular mounting for gun turret or other rotating fitting. BARQUE.—A three masted vessel square-rigged on fore and main, mizzen. and BARQUENTINE.—A fore three and aft masted rigged vessel on square- rigged on foremast, fore and aft rigged on main and mizzen. BEAM.—The greatest width of a boat, also one of the timbers on which the deck is laid. BEATING SHEET.—A line controlling the angle to which the main boom of a yacht may swing. BELAY.—To make fast a rope, to stop, BELAYING PIN.—A brass or wooden pin set jn a pin rail for securing running rigging. BEND.—To fasten in place. BILGE,.—The portion of the hull below water, also the inside collects, of the hull where extrancous water BINNACLE.—A container for a ship’s compass. BLOCK.—A pulley which is used in rigging. BLUSHING.—Whitening of cellulose liquids due to chemical reaction with water vapour on drying. BOAT.—Formerly a vessel built on bent frames (a ship used sawn frames), but nowadays any vessel which is capable of being hoisted aboard another applied vessel; to any except vessel at in the all. R.N., generally age CHOCKS.—Wood cradles for stowing a BOLLARD.—Sturdy posts normally set in for making off cables, etc. BOLT ROPE.—A rope sewed to the edge sail for strengthening, BOOM.—A spar at the foot of the sail, BOOT TOP.—A painted line or ch at the hull water line, BOW.—The BOWSIE ‘ she I eee panes forward part of a vessel. (Bowser).—A small slide model’s rigging. pairs CABLE LAID.—A to the left. CAM.—A rotating oot SS disc which the strands run bearing against an arm, and shaped so that the arm is raised or lowered at certain points of rotation. CAMBER.—The thwartship curve of a deck. CAPSTAN.—A drum revolving vertically, used for hauling in a rope, etc. CARAVEL.—A galleon, but three masted considerably CATALYST.—A_ chemical vessel smaller. reagent similar to a which when mixed with other materials starts an irreversible chemical change. CENTREBOARD.—The fin keel which can be raised or lowered in a well to provide additional side area for shallow draft boats. CENTRE OF GRAVITY.—The point through which the weight of the boat may be said to act. CHAIN PIPE.—A casting set in the deck through which the anchor chain passes into the chain locker. CHAIN PLATE.—A fitting for the attachment the main mast shrouds at their lower ends. CHAMFER.—An angle planed into a piece timber, out of square with .he main faces. CHINE.—The line where the sides of thm of of boat meet the bottom, forming a sharp angle. CLEAT.—A fitting with two horns for making fast a rope. CLEW.—The lower corner of a square sail, or the aft corner of a fore and aft sail. CLINCHER BUILT.—A_ method of planking where the lower edge of each plank overlaps the upper edge of the plank below. CLIPPER.—A three or four mast square-rig vessel employing a very narrow beam hull. COAMING.—A raised structure round a hatchway or cockpit to prevent water entering. COMPANIONWAY.—A from the main deck. COMPRESSION combustion fected by the gases. ‘ rope in — BALLOON JIB.—A very large headsail, sometimes used on a racing yacht. stairway Icading IGNITION.—A type engine in which ae down of internal combustion is ef- the heat generated by ‘compression of ; CONVECTION COOLING.—A method of cooling an engine by means of a water header tank. * GLOSSARY employing the natural tendency of warmed water to rise, thus producing circulation. COUNTER.—The overhang of the stern. COURSE.—The main sail on a square-rigged mast. ies loop of rope spliced into the edge ea of a sail. CROSSIACK.—The yard lowest mizzen the on mast. CROSS-TREES.—Light timbers to spread the ris~ ging of a mast. CROSS-SECTION.—A true section of a hull, etc., at any point looking along the longitudinal axis, CUTWATER.—The part of the stem on the actual water line. CUTTER.—Formerly a single masted vessel carrying a square sail and a boom mainsail, topsail and gaff topsail; nowadays normally fore and aft rigged. 93 FURL.—To bunch up and secure sails. FUTTOCK.—A portion of a frame; in a ship _— frame usually comprises six to eight futtocks. GAFF.—A spar on the afterside of the mast supporting the head of a fore and aft sail. GAFF TOPSAIL.—A triangular sail filling in the space between the gaff and the top mast. GALLEON.—iS5th, 16th or 17th century sailing vessel, notable for a high poop. GALLOWS FRAME.—Framework carrying a platform for stowing boats, etc., above deck level. GANGWAY.—An opening in the bulwarks. GANGWAY LADDER (Accommodation Ladder). —Steps leading down the ship’s side. nied STRAKE.—The plank next to: the keel. DAVIT.—A type of small ‘crane for hoisting and lowering ships boats. DEADEYE.—A wooden block grooved round the periphery, and equipped with three holes to pass ropes, DEADRISE.—The angle of’a ship’s bottom from the horizontal, DEY eon:.—Normally fhe solid wood part of DECK PIPE.—The upper lp of the anchor hawse a kee pipes. DISPLACEMENT.—The weight of the volume of water displaced by a boit, ic. the weight of the boat itself. DRAFT (Draught).—The distance between «the waterline and the lowest point of the keel. DOWEL.—Timber, usually birch, purchased in strips of circular section. EARING.—A rope used itf bending a sail, particularly at the corners of a square sail. of method CONSTRUCTION.—A EGG-BOX building where structural members are all halved together. EYEBOLT.—A bolt with a loose ring in its head. EYEPLATE.—A_ small plate incorporating an cye used in securing or passing a line. mM FAIRLEAD.—A fitting for guiding a rope. FALL.—A rope which with blocks comprises a e.g. boat falls as fitted to davits. tackle, FEATHER EDGE.—A timber which is tapered off to a knife edge along one side. FLANGE.—A rim projecting at right angles. FLEMISH COIL.—A coil of rope in which each coil lies flat, giving the appearance of a mat. FLYING JIB.—The outermost headsail. FOOT-ROPE.—A rope moynted on a square yard FORE FORE (Forward).—Towards AND AFT.—From the stem bow. to ; stern along the longitudinal axis. FORECASTLE.—Space beneath the forward portion of the deck, usually abbreviated to fo’c’sl, FOREPOOE, ~The point where the stem meets the eel, FOREMAST.—The mast nearest the bow. FORESAIL.—The largest sail set on the foremast. FORESTAY.—A stay running down from the mast, and*made to brace the mast against backward stresses. ae .—A thwartship structural member of the ull.’ FULCRUM.—The takes place. point about which a relatively soft rotation packing piece between two joined surfaces. GOOSENECK.—A swivel joint by which the heel of a boom is held to the mast. GOVERNOR.—A mechanism fitted to some motors to limit the maximum speed. GUDGEON.—An eye in which a rudder pintle turns. GUNWALE.—The top-most edge of the deck, or a small boat rail. GUY.—A line used to steady a spar. GUYING.—Carrying out a gye. GYBE.—A change of course relative to the wind when running, with the main boom swinging to the opposite side. GYE.—To change tack intentionally when sailing also the mechanism used to to windward; change tack. HALLIARD (Halyard).—The rope used to hoist sails or yards, etc. HATCH.—An opening for the deck; the cover for such an opening. HAWSE PIPE.—The pipe emerging in the side of the bow through which the anchor chain passes. HAWSER.—A heavy rope. HAWSER LAID.—A run to the right. ¢ on which to stand. GASKET.—A rope wound round the furled sail; rope in which the strands HEAD.—The top or outboard end, e.g. mast head, etc.; the *op side or corner of a sail. HEADSAILS.—Fore and aft sails forward of the foremast. HEEL.—The bottom or inboard end, e.g. mast heel; the canted angle at which a vessel sails. HELM.—The tiller or steering mechanism. HOUNDS.—A mast fitting carrying cross trees, etc. HORSE.—A thwartship rail to which a model’s sheets are hooked: IDLER GEAR.—A small gear doing no work, but reversing the rotation of a second gear. INTERNAL COMBUSTION ENGINE.—Any engine deriving its power from the expansion of gases burned internally. IRONS.—“‘In irons’—when a boat comes up into wind and will not pay off, she is in irons. The condition is accompanied by sail-shaking, etc. JACK LINE.—A taut Hine on which a sail is bent. JAWS.—A type of wooden crutch at the heel of a boom engaging the mast. JIB.—A triangular sail set on a stay forward of the mast. 94 JIB BOAT MODELLING BOOM.—A sprit; spar extending beyond the bow- the spar attached to the foot of a model yacht jib. JIG.—An internal or external structural assuring accurate alignment. JIGGER.—A small fore and aft sail mast of a yawl, etc. member, on the after PLATE AND BULB.—A keel consisting of a thin Plate, swelling POOP.—The out raised at deck the bottom at the for the after end of the vessel; in the navy, the quarter deck. PORT.—The left-hand side of a ship; an ing ir the side of a hull lead. or . open- deck. JOGGLING.—The irregular jointing of deck planks into a kingplank or different direction. JUMPER STRUT.—A other plank strut backstay. running used to in a extend a QUADRANT.—A to the keel KETCH.—A two masted vessel with a small after mast stepped forward KILN-DRYING.—A of the process rudder of baking a kiln to dry off sap. post. timber in KINGPLANK.—The central plank of the deck running fore and aft. KITCHIN RUDDER.—A device consisting of two cups fitting round the propeller, and adjustable for steering or for speed control and movement astern, the build bonded together. LANYARD.—A fast. light up rope in for several making layers anything attachment point a circle; vessel of a navi- between stern the after rigging. RAKE.—The angle of the mast from the vertical, the angle of the stem or transom. RATLINE.—Small ropes passing across to form a ladder, REEF,.—To reduce sail area. REEVE.—To run a line through a hole. RESIN a BONDED.—Glued water and heat together proof RIB AND PLANK.—A resin hull by shrouds means of glue, built by planking on to ribs which remain part of the finished struc- ture. ROUND BILGE.—A boat in which turn of bilge is a continual curve. RUBBING STRAKE (Rubber).—A fore and timber LAMINATE.—To of gational instrument. QUARTER.—The side of the and KEDGE.—A type of light anchor. KEEL.—The backbone of a vessel. KEELSON.—The heavy timber fitted for reinforcement. segment laid externally to protect the the aft planking. RUNNING LIGHTS (Steaming Lights).—Lights carried on each side of a. vessel in motion, red to port and green to starboard. RUNNING etc., RIGGING.—Lines which are moved LARBOARD,—Disused term ior port side. LATEEN.—A large triangular sail set at an angle to the mast. LEACH.—The after edge of a fore and aft sail ; standing rigging for masts, LIFT.—A rope attached to the end of a spar sup- SCARF.—A joint between SCHNORKEL.—A device is the ‘ for from setting time permanent saila to bracing, time, etc. the sides of a square sail. porting its Position. weight and determining its vertical LIVERPOOL BOY.—A light rubber band on an adjustable line, attached to a jib-boom and tending to keep the fib on one tack. LOOF.—That part of a ship where the beam nartows towards the stern. LUFF.—The forward edge of a fore and aft sail; to allow a vessel to come up to the wind. MAIN MAST.—The middle of a three masted vessel, or after mast of a two master, except a yawl or ketch where it is the forward mast. MAINSAIL.—The largest sail on the main mast. MIZZEN MAST.—The after mast. MOCK-UP.—To make a dummy model in the same size as the type. non-working finished proto- two blending them into one. which can by a submerged submarine, may be drawn into the boat. SCHOONER.—A fore pieces and of timber, be surfaced through aft rigged anything from two to seven masts. schooner is two masted carrying a and top gallant sail on the fore. which vessel air with A_ topsail square top SEIZE.—To bind with light cord. SCUPPEBR.—A drain cut through a bulwark. SELVEDGE.—The manufactured edge of cloth. SHACKLE.—A U-shaped iron fitting with a pin closing the open end. SHARPIE.—A hard chine boat. SHEAVE.—The grooved wheel in a block. SHEER.—The curve of a deck viewed from abeam; the concavity of the sides or bottom. SHEET.—The rope attached to the clew of a sail. SHIP.—Strictly a three or four mast vessel, squarerigged on all masts. SHOCK MOUNTING.—Mounting on rubber, etc., go. that vibration, etc., is not transmitted to the O.D.—Outside Diameter. (I.D. is inside diameter.) tting, SIGNAL Paratus, PARREL.—A band or strap securing a yard to a mast, but allowing the yard to be moved up and down. PAWL.—A pivoted lever engaging in pockets in a wheel, preventing the wheel from moving back. PAY OFF.—To turn away from the wind. PEAK.—The tip of a sail attached thereto ; mum power PINTLE.—The is gaff, fitted a hinge movement. the corner of a the speed of which maxi- produced pin or to by a an engine. rudder to provide GENERATOR.—A comparison with piece of wireless ap- which enables a trans- mitter’s frequency to be determined. SKIN.—The covering of planking forming sides and bottom of the hull, SKYLIGHT.—A window. over a cabin, etc, SLOOP.—A vessel, single masted fore and SOLENOID.—An iron core which into a wire coil when the coil energised. is is aft the rigged withdrawn electrically SPANKER.—The fore and aft sail on the mizzen mast, SPAR.—A yard, gaff or boom. SPINNAKER.—A large triangular sail set on a 95 GLOSSARY the of the above hull boom on the opposite side of the mast to the main boom, and used when running. SPREADER.—A strut extending from the cross- TEAS Se SPRITSAIL.—A square sail set beneath the bow- pg alee ring or pulley sliding across a SQUARE-RIGGED.—Equipped with square sails the yards of which are thwartship. STANCHION.—The vertical pillars carrying rails. STARBOARD.—The right side of the boat look- i sides TOPSIDES.—The waterline. trees to spread the backstays. a sprit. boat. Tee flat, usually upright, stern of arse. “paeies inward slope of the top- TURNBUCKLE.—A screw device for tightening rigging. ing forward. STAY.—A heavy rope used to brace a mast, STEM.—The foremost timber in a hull. STERN.—The after end of a ship. STERN POST.—A vertical timber joined to after end. VANE the at it hull. eid plank STRINGER.—A fore and aft. light running the structural of length member a constant —€ STERN SHEETS.—The space in the stern of the small boat. GEAR.—A device angle rope to used to the wind. steadying the steer outer a model end of a gaff. the WAIST.—The mid portion of the deck. WALE.—A heavy strake running fore and aft. WATERLINE.—The line at which a vessel rides running STROPPING.—Encircling a block with a rope. STUFFING BOX.—A short bearing through which a propeller shaft emerges from the hull. boat a of part SUPERSTRUCTURE.—The when afloat. WATERWAY .—A channel. deck serving as a gutter. WEAR.—To above deck. level. SWEAT.—To run solder through a joint by means of a blowlamp, etc. change tack tunning while round running. WHIP.—A single block fitted with a springiness natural to timber, etc. line; the the WINCH.—An engine fitted with a drum for hold.ing a rope. peo LASS.—A mechanical device for hoisting an TACK.—The lower forward corner of a fore and aft sail; the rope that holds down the forward clew of a square sail when on the wind; to anchor. WORM.—To lay thin twine between the of a rope to present a smooth surface; used sail into wind. TACKLE.—Gear composed of blocks and rope. TAFFRAIL.—A rail round the stern. TEMPLATE.—A pattern cut to check the shape. THROAT.—The forward upper corner of the fore and aft sail. when required. considerable XEBEC.—Lateen rigged reduction Mediterranean in strands a gear speed is vessel. THWART.—A small boat seat. THWARTSHIP.—From side to side. TILLBR.—A bar connected to the rudder head and moved from side to side. TIMBERHEAD.—Part of the frame projecting above deck against which the bulwarks are built. TOP HAMPER.—The rigging, etc., above deck. TOPPING LIFT.—A tackle holding up the end ot a boom or yard. » YARD.—A horizontal spar from which a square sail is set. YARD ARM.—The outer eighth of a yard. YAWL.—A fore and aft rig consisting of two masts, the after one being very small and stepped behind the sternpost. & Nearly 100 ship. power boat, and yacht designs by the author are available, and thousands of successful models have been built from them. Most are well within the scope of the newcomer (see sample reproduction overleaf) and all are available from: MODEL MAKER PLANS SERVICE, P.O. BOX 35, HEMEL HEMPSTEAD, HERTS., HP1 1EE Send 20p for our latest Plans Handbook No. 2 which illustrates a wide range of models of all types, including many M.Y.A. class racing yachts, power boats, hydroplanes, etc. wa0enw LNaMUSAraY Oasinosic 40MHOIS‘5eTEaAD8dNL ‘SNOWIYRT¥M31 A-_ vus3OdIN vPe 1HI JTS7HeINaYdv O73L4 |HaALOvo@sn OSisxmQvEe YFIWS-dIN3ZSaTBNLOBSYVNHESNL awineO r Ky caNeIs30 Ae Wy)Sa3IwAs A4HDI0BG.O iVMas0e 920SuARLNo1nUOH8ad.$40ND 0aU4uNWLonS%sch GHwI-OMKdv2 @LSNIBMdVHOD ane