O~D =U NUEWAIERIPHONOS!, 10 CONTROL mwmremooeos sarowv M/COUD {| -USA$3.50 CANADA $3.95 09 71896°4 604 – by ROD CARR Mi OST R/C ENTHUSIASTS focus a good deal of their effort on the power that moves the vehicle. Model yachtsmen, however, generally unwrap their sails, make sure that the most pointed ends are at the top of the mast and the top of the jib stay and then charge toward the starting line with little worry about how the yacht will be powered. Much has been written about the trimming of the sails, ie., the presentation of the sails to the wind at the proper angle for a specific result. There’s very little data about a sail crosssection’s absolute shape, which is really critical. | have 20 years experience as a model yacht sailmaker, and for this article, I was helped by photographer Larry Robinson, of Seattle, WA. SETTING SAILS Before | discuss the sails, a few words about the supporting strucMy EC/12 FOXY LADY V, with 1-inch draft stripes painted on the main and jib. Make Your Sails A Proper Cross Section Enhances Performance ture are in order. For the best overall results, start in a medium breeze (3 to 8 knots) with a mast that’s absolutely straight. (The jib stay should sag only very little. Here are the jib draft stripes. Being able to assess the shape and freeze itintime provides the chance to study it in detail. This g-Forse 12-meter |. . prototype exhibits what |… appear to be mainsail \–“”—= faults. They are actually * the result of a bending mast, not a sailmaker’s error. The best way to test this on shore is by putting the hull on its side and then sighting down the mast.) Because the sail won’t be carrying a heavy wind, take photographs of your yacht while it’s on the water, especially while beating to weather. (Use black and white film.) You may be surprised at what you see. Project the negatives from a 2×2 slide holder onto a wall, and hold a straightedge against the projected image of the mast and jib stay. No analysis done on the sails will be worthwhile if you don’t start with a straight mast and jibstay. Some model yacht sailmakers put too much cloth in the luffs of their sails. This is called “luff round,” and it’s measured as a maximum departure from the straight line between the sail’s head and its tack. The proper amount of luff round is a function of the fore and aft dimensions of the sail, the wind speed range being provided for, and the mast shape required for the sail to set well. A good sailmaker should provide you with a written description of how the sails SEPTEMBER 1991 67 Make Your Sails should be set. If all you get is a rolled-up jib and main, you’ll have to do a good deal of experimenting before you get it right. You may even have to add, subtract or change the positions of the shrouds that support your mast. I’ve seen an East Coast 12-meter mainsail cut in such a way that the mast was bent 3/4 inch forward in the middle to allow the sail to set woven, so Luff | <¢ Chord mainsails can be made with Figure 1 seam panels that run parallel to the foot of the sail. That way, they'll be more useful for reference during analysis. eThe second method involves providing additional reference marks—horizontal stripes, which are applied to the sail. The 1987 America’s Cup defender “Kooka- burra” had wide, black “draft” stripes on both its mainsail and its jib. These were monitored by a video camera from the mast, and adjusted while sailing. I’ve applied stripes to my EC/12 Foxy Lady V (see photo); their color matches the hull. As a bonus, it’s easier for me to pick my boat out of the crowd at the starting line. Add the stripes after the sails have been mounted on the rig, so that they can be aligned vertically. If you The same g-Forse sails ona straight mast. Here, there’s too much luff tension, pulling excess cloth to the mast, paint one stripe from flattening the sail and reducing drive. the luff of the jib, past the mast to the leech of properly. It can be done, but the mainsail, you'll have a measuring “mast bend” is a better idea of how the sails really time-consuming job, work together. I use model whereas just about anyone can paints for the stripes (either tell whether something is or isn’t sprayed or brushed on), and straight. my stripes are generally about 1 inch wide. MARKING THE SAILS You can analyze the crosssectional shape of the sails in two ways: eYou can use this method if your sails are paneled. On jibs, the panels generally run horizontally, i.e., in the direction that the wind will pass over them. Paneled mainsails, however, usually have their seams running perpendicular to the leech. Given the strength of the Mylar fabrics used in model yacht sails today, there’s no longer a reason for the mainsail panels to be joined in that way. They were constructed like that when made of woven fabrics so that a thread line would parallel the leech and help them handle high winds without losing their shape. Mylar isn’t 68 RADIO CONTROL BOAT MODELER PHOTOGRAPHING THE SAILS You'll need a partner to help with this step. Set the sails flat for sailing as close to the wind as possible (close-hauled), then have your assistant hold the boat into the wind, (i.e., slightly off from close-hauled). The sails should be a little too tight so that they'll be wellfilled by the wind. Keep the sails full, then allow the boat to list 25 degrees or so. The photographer should then take a picture of the sail from below the gunwale at the foot of the mast, getting as much of the sail plan in the picture as possible. A careful selection © | Leech : of aperture and speed will allow the draft stripes to be in focus. Of course, “main only” or “jib only” photos are possible. Avoid superwide-angle lenses because of the curvature they add to the final photo. TARGET CONFIGURATIONS I'll assume that the faults you may observe aren’t the results of faulty spar shaping, improper tensioning of outhauls, halyards or vangs, or physical damage to the sails themselves. Let’s say the sails were set on perfect spars and rigging. Obviously, you should check that nothing else is wrong before you condemn the sail or the sailmaker. The results of improper rigging The ainsail of an M-class boat. Notice the parallel chord lines that indicate a lack of twist in the sail. The top two chords run along the panel seams, and the bottom chord runs along the draft stripe. These are the wo a somewhat sla dyad foran M-class dacronjibon jib stay. PHOTOS BY LARRY ROBINSON AND ROD CARR EXCE continuation of the sail form forward of its leading edge. or excess tension, for example, can easily be mistaken for bad If you study your photographs carefully, you can determine the entry angles. Entry angle can be influ- sails. If your mainsail is too flat and has wrinkles, check it. It could be that too much backstay tension has bent the mast, which is now pulling on the sail. Easing the backstay tension will solve this dilemma. Likewise, if the enced dramatically by luff tension in the sailcloth. downhaul tension is too great, ha ena b sail ages. Battens twist offand Thisis logeopensasa your sail will appear pulled and flat—a “wiggle” in the draft stripe could tip you off to this problem (see photos). If you realize that these kinds of diagnoses are difficult to make while the boat is moving, the waves are dancing and the sails are responding to the wind, you know that the photos are well worth the effort. ech stretches and becomes loose. Notice the very bottom seam in the mainsail. ultimately the Notice in Figure 2 that simply setting the depth to be built into the sail doesn’t fix the actual sail section shape. In the drawing, all sails have the same chord length and the same depth, yet their shapes differ drastically. Note that “a,” “b,” and “c” have the maxi- CAMBER LEECHES Sail leeches (the vertical edges of a square sail; the after edge of a foreand-aft sail) should allow for an easy passage of air, and when closehauled, they should be approximately parallel to the boat’s center line in the lower part of the sail. The photos you take will help you to determine this, as will sighting down the mast when the boat is on shore. If the mainsail directs air windward, the result is substantial windward helm that pushes the mum depth at the same distance The camber ratio of depth to chord can be expressed as a percentage by dividing depth by chord (see Figure 1). According to aft of the leading edge, but their shapes are still very different. The next parameter to ap- proach as you try to quantify your sail’s shape is the location of the sail’s maximum draft, or depth. Measure aft from the leading edge of the sail and express that distance as a percentage of the chord. Ross indicates that maximum aerodynamic forces occur when the maximum draft is between 33 Ross, a range of camber ratios is encountered in model yacht sails; from flat sails with camber ratios of 1:20 (5 percent) to very full sails at 1:5.5 (18 percent). A good, all-purpose sail has a camber ratio of 1:10, or 10 percent. Adjust the halyard, or downhaul, enough to remove any wrinkles, but not so tightly that it pulls the cloth forward from the body of the sail. percent and 40 percent of the sail chord. These PS: a — << “4 ae cid 10 10' > > draft-forward sails provide excellent acceleration. As a result, model yacht sails are typically designed to have maximum draft at approximately 40 percent of their chords (see Figure 2e). This recognizes the shortness of some courses and the importance of accelerating out of tacks, which is such a big part of “round-the-buoys” racing. Recent work on sails that were made for very high speeds has placed the maximum draft as far aft as Look at the area from below the lowest batten to the clew patch, and at the wrinkles forward of the battens on both sails. All of these things are signs of a loose leech, and a sail that’s ready for retirement. 50 percent. ENTRY ANGLE Figure 2 The entry angle is the angle ~ between the chord and the boat’s stern leeward. A loose leech can be hard to spot. The best indication of one is when, even with plenty of tension between the head and the clew (one of the sail’s two lower corners), the battens fall leeward. The result is a large increase in drag and, possibly, the development of a lot of lee (Continued on page 75) SEPTEMBER 1991 69 Fast! ae ‘TRICEPTOR New! | Unique 19’/2”’ wide, 3912” long .40 size 3-Hull Design makes for a very fast, yet stable Airboat. Available ready-to-run or in kit form. Constructed of polyester fiberglass with white gelcoat finish. Kits can be assembled in 2-4 hours. FOR MORE INFORMATION, PRICES, VIDEOS — Contact: (904) 724-2251 |2689 Kersey Dr. W. DeGoursey Enterprises, Inc. HUSTLER (Continued from page 74) The Hustler’s prop cavitated for a moment, but after running approximately 20 feet, the hull got up on step and accelerated nicely. The water was calm, and the model ran rather “flat.” The boat felt balanced, but when I applied left rudder, it seemed to skid in turns. I attribute this to the hull’s shape—a modified vee—and its rather smooth strakes. The Hustler didn’t spin out; it just seemed “soft” when it edged around corners. (The hull seems to have been vacu-formed over a mold, and this has produced the strakes’ smoothed-over shape.) The Hustler doesn’t come with turn fins or trim tabs, and adding them would be the first logical step toward improving its performance in turns. As is, it’s a fine, powerful sport model. Needing little trim, it runs straight and hard right off the workbench. The Hustler doesn’t pretend to compete with models that cost two or three times as much. Given its reasonable price and the little assembly required to put it together, I rate the Hustler as a good value, and its performance can satisfy sport mariners. I like my Tupperware® boat! *Here’s the address of the company featured in this article: . Hobby Dynamics Distributors, P.O. Box 3726, Champaign, IL 61826. JR Propo; distributed by Hobby Dynamics.Q Jacksonville, FL 32216] MAKE SAILS EXCEL (Continued from page 69) helm. Time for new sails! TWIST If the chord lines associated with the draft stripes aren’t parallel as you raise a sail, if you look behind the sail, you’ll see that each batten is at a progressively different angle to the main boom, and the sail has a “twist.” In model yacht sails, only alittle twist is useful—certainly no more than about 5 degrees. Use the vang and the sheet to control mainsail twist. Jib twist is a combination of jibstay tension, jib-club offset and topping lift tension. Twist is important enough for an entire article, sol’ll simply say for (Continued on page 76) Electrifying News trom OCTURA MODELS. INC. Pioneer Producer of Proven, Precision, Performance Propellers for R/C Model Power Boats! For electric powered boats, using direct-drive with .125 diameter propeller shafts, OCTURA now has available 11 metal propellers. These are intended for use on 540 and 05 motors as well as the special 540 { motor hand rotation unless otherwise noted. Available in Beryllium Copper or Aluminum at the same price! Phone & Fax # (708) 674-7351 THE R/C MODEL BOAT PROPELLER PEOPLE …SINCE 1954! Order direct only if not available from your local hobby shop. Add $1.50 total for shipping. Ill. residents add 7% sales tax. 1427 X427 oo The R/C Model Boat Propeller People! CTURA X430RH wind motors. Install an OCTURA propeller on your direct-drive boat and you’ll be amazed at the performance difference. Also available is a drive dog, the OC4D. All are left 0930 Cobalt 40 1630 1732 1930 hot wind X432 hi torque X435 0937/3 OC4D Drive Dog $8.95 each 9.25 each 12.00 each 1.75 each =) OCTURA MODELS, INC. 7351 N. Hamlin Avenue ¢e Skokie, IL 60076 SEPTEMBER 1991 75 OFFSHORE MODEL BOAT CO (716) 283-0059 519 CAYUGA DRIVE, NIAGARA FALLS, NY 14304 Edward R. Barnes, Jr. (owner/designer) MAKE SAILS EXCEL John de Graff, Inc., 1972. Marchaj, C.A.; “Aero-Hydrodynam- (Continued from page 75) now that you should try to keep it to a minimum. These sources were used for research of this article: Howard-Williams, Jeremy; “Sails,” ics of Sailing,” Dodd, Mead and Company, 1979. Ross, Wallace; “Sail Power,” Alfred A. Knopf, 1975. Whidden, Tom & Levitt, Michael; “The Art and Science of Sails,” St. Martin’s Press, 1990. qo A SPECIAL MESSAGE TO RETAILERS MAGINE the benefits of drawing many more regular customers into your store every month. Imagine adding a popular, profitable—and returnable—hobby product to your store. By stocking Model Airplane News, Radio Control Car Action, the Radio Control Action Series and Radio Control Boat Modeler, you’ll accomplish both! These are the most informative and entertaining modeling magazines available to the R/C consumer—and they’re in / tremendous demand. These magazines will / actually stimulate more sales of R/C airplanes, cars, boats and accessories for you. If you aren’t already stocking Air Age magazines, please call us toll-free, and we’ll let you 7 know how they can make money for you. BUILD A MOTOR (Continued from page 59) faster setups. This process should help you avoid having a motor meltdown. This outboard will push 22- to 32inch hulls at speeds equal to those of many 3.5cc glow-power models. (Continued on page 82) We think many of our read- ers have ideas that are worth sharing. How many times have you read an article and said, “I could do that!” or “That’s not the only way to do that; my way is easier!” Could very well be! Here’s your chance. We’re expanding Radio Control! Boat Modeler and are looking for additional contributors to help us accomplish this objective. Of key importance is the ability to take good photographs; the writing we can help you with. Interested? It’s much easier than you might think! Let’s hear from you. Send in your ideas, articles, thoughts and photos; we’re looking forward to it. Tom Atwood Air Age Publishing 251 Danbury Road Wilton, CT 06897 76 RADIO CONTROL BOAT MODELER





