-Tornado’s Performance “*Install-a Fiberglass,.DeckTMTM” =. on 2 cuvoust = | 718896″46040 WAREHOUSE HOBBIES FIRS IVIQIE ~~ | © PRATHER FUN CRUISER si ® m 4 — . © AEROTECH 40/60 TUNNEL © BLACKSTIA 35 SAILBO AT | ee tae CONSTRUCTION be & . L Scepter Racing “= Sailboat novice skippers 26 RADIO by THOMAS J. CONTROL BOAT MODELER HOULE HIS ARTICLE shows you the building techniques that you might use to build an AMYA*# (American Model Yachting Association) U.S. 1-Meter Class racing sailboat. Bob Debow designed the boat—the Scepter— that’s featured here. As the name of the class implies, the hulls are between 39 and 39% inches long. The maximum allowable sail area is 600 square inches. The first thing I look for when I build a boat is a dead-straight i board that’s at least 48 inches long. A 12×48-inch slab of 5%- or ¥-inch-thick plywood will do, as long as it isn’t warped, but I prefer to use 2×6-inch Douglas fir. I can easily clamp it in my shop vise to bring the hull up to a comfortable working height. — CONSTRUCTION I draw a center line along the board and then erect temporary Here’s a U.S. 1-meter building board with the shadows erected. The shadows have been notched to position the keelson and the sheer stringers. The ‘%-inch plywood stem has been glued into place. ii de shadows (frames), spacing them Clear plastic wrap protects the foam-core shadows. The sheers and the keelson are in-place. Check the hull to ensure that the stringers run fair and true; there shouldn’t be any bumps or depressions. out as specified on the plans. A Ya-inch-square pine block at each station will ensure that the temporary shadows stay vertical and square to the center line. board and to the first shadow. You’ll cut away the bottom of the stem when the boat is removed from the board. The pine wood or foam board; some builders lami- sheers and keelson laminations are then laid into the notches in the shadows and nate the two together. I like foam board glued to the stem. I always eyeball the fair- because it can pins. After the ness and runout of the sheers and the keelson. Sometimes, the shadows need a little trimming or shimming to make the shadows have hull outlines smooth and symmetrical. The shadows can be cut out of thin ply- accept planking been set into place, they PLANKING THE HULL must be pro- Planking is next. You’ll use about three tected from the use to plank the sheets of ¥gx4x48-inch medium-hard balsa to plank a typical U.S. 1-meter boat. I cut the sheets into ¥s-inch-wide hull. Clear plas- strips. You’ll also need five ¥ex¥%x48-inch tic wrap works and one ¥x’/2×48-inch clear pine or spruce strips for the keelson and sheer glue that you well, because it clings to the shadows SaaS The view from the stern. | have started to plank the Scepter’s hull with Vax34inch hard-balsa strips. This hull has hard chines that run back to station 4 before easing into a round bottom Shape. The vee-bottom bow minimizes “submarining” when the model sails downwind. and clamps. These are available as sawn spruce members at a hobby shop, or you most adhesives can rip your own. (Redwood or cedar will won’t stick to it. do as well, but don’t use balsa.) After the I always start planking at the keelson, shadows have been erected, attaching one balsa plank to each side before moving outward. Alternating the glue ¥s- planks (gluing one to the left side of the inch-thick ply- wood stem to hull and then one to the right side) distributes the force that the planks generate. the building When I reach the point at which the the planks must be severely bent or twisted, I switch to the sheers and plank up from there. The photos show this process. Because I usually cover the hull with fiber- glass and paint, I don’t worry too much about glue stains or carefully fitting the SPECIFICATIONS Type: 1-meter racing sailboat Length: 39 in. Beam: 7 in. Hull material: Wood (baisa hull built over shadows) Sail area: 597 sq. in. (total) No. of channels req’d: 2 (rudder and sail control) Comments: the Scepter is great for novices. Its wooden hull is built over shadows that are attached to a strong building board. After the hull has been completely planked and finished with fiberglass cloth and resin, it’s removed from the shadows, and the interior of the hull is finished. Bob Debow designed the original AMYA O-class Scepter sailboat, and the author obtained his permission to publish this construc- planks. I’ve seen striking redwood hulls that were planked this way and then varnished, however I’ve planked hulls using white glue, yellow carpenter’s glue (alipi and CA qhues what I’ve read e none of my whit nc This view from the bow shows that the bottom planking is complete. Now, !’ll plank the hull from the sheers. The hull has been cgi letely planked. After the pins have been removed, b ocksand the hull across the grain. Fill the low spots with a vinyl filler. low-glued Here, the Scepter’s hull is ready to be fiberglassed. A 1.5-ounce cloth is draped over the hull. Leave at least 1 inch of excess cloth around the hull. When the cloth is wetted with the resin, it will generally assume the shape of the hull. If not, cut some small slits in the cloth to pull it snugly to the wood. ther glue is waterproof. And I’ve sailed these boats for several years. I attribute their integrity to the fact that I always var- Before | removed the hull from the building board, | covered it with three coats of epoxy resin, sanding between each coat. The finished rudder and the 5-pound fin and lead bulb are ready to be attached to the hull. block and fresh 50-grit sandpaper. End with 120-grit sandpaper to remove small nish or epoxy the hull interior and the underside of the deck before I permanently attach the deck to the hull. Slow-setting CA can also be used for imperfections. An old mariner once told me to run the sanding block at a 45-degree angle to the grain of the balsa. This removes the “high spots” quickly. When you sand between the shadows, be careful not to create “low spots.” planking; it adheres well and permits you to plank at warp speed. Make sure that your When the hull is fair and smooth, I cover shop is well-ventilated: at best, the fumes are it with 142-ounce fiberglass cloth. To save weight, I’ve tried ¥-ounce cloth, but it didn’t provide any hull strength or protec- overwhelmingly nasty. [Editor’s note: “odor- tion. You might try two layers of 34-ounce less” CA glues are now available from many glue suppliers.] The hull is ready for decking. The radio Here’s a close-up of the — open atches and ia system, a“ the cross-members have fin-box assembly that hasbeen installed. Note the blocks amidship been permanently installed between the keelson and the king- plank. at the sheers. They retain the shroud chain-plate screws. Small nylon blocks under the deck guide the sheets back to the sail winch. cloth, placing the first layer at 45 degrees to the keelson and the second at 45 degrees to the weave of the first. I’ve used polyester resin and several epoxy formulas on my boats. I think Hobbypoxy* Formula-2 is the all-around winner. It doesn’t run, it’s easy to sand, and, above all, it doesn’t have a noxious odor. The instructions tell you not to thin FINISHING THE HULL After the hull has been planked, I carefully sand it to remove the usual accumulation of glue blobs, high spots, etc. Do this with a long The U.S. 1-Meter Class | A MYA members Bob Debow and Bob Jensen created the Olympic 1-Meter Class in 1983. Unfortunately, the U.S. Olympic Committee ordered them to drop “Olympic” from the name, so it became simply the U.S. 1-Meter Class, but the class symbol is still an “O.” Debow’s 1-meter design—the Scepter— features the narrow beam and the relatively deep draft that’s favored by many West Coast skippers. Having raced one myself, | can attest to its performance—particularly in heavy winds. Detailed building instructions and frame patterns for this boat and more than a dozen other 1-meter designs are available from the NN 28 RADIO CONTROL BOAT MODELER nate AMYA 1-Meter Class secretary Steve Andre”. According to him, there are almost 700 boats registered in the class. | guess there are hundreds—if not thousands—more that aren’t registered. Debow and Jensen’s original intention was for the class to use—as Debow says—‘that high-tech product: wood,” and the two men developed a hull shape that could be planked with %-inch-thick balsa strips over a temporary form. After being sanded, the hull is covered with fiberglass cloth and epoxy resin. The deck can be Y%a-inch or ‘42-inch plywood. The sturdy finished product costs less than $200— including a dry, 2-channel radio—so a freshman skipper can easily put himself at the helm in a very hot, growing racing class. If you don’t want to scratch-build, you can order a complete kit—the Soling—from Victor Engineering’. It’s easy to build and meets all the U.S. 1-meter class rules. It includes a molded plastic hull and sails, but you’ll need to supply a sail winch and a 2-channel radio. The kingplank, which runs the length of the hull, has been installed. The reverse transom, the rudder tube and its crosswise brace, or thwart, have also been installed. One cross-member has been installed midship to hold the hull at the correct width. it with epoxy thinners, but I’ve used epoxy thinner and acetone, and both seemed to work. Whatever you use should be thin enough to brush onto the hull with a disposable brush. Each coat of resin should be sanded smooth before the next one is applied. Three coats will fill _ | the fiberglass cloth and provide a mirror- like finish that’s ready for priming. After priming, fill the inevitable low spots with auto-body spot filler. After sanding and priming the hull again, you can remove it from the building board. Before I do this, however, I lightly mark the water line if I’m going to include it as part of my final paint scheme. (Shadows are drawn so that when they’re erected on the building board, the water line always runs parallel to the board’s surface.) Using a wooden block that has been drilled to hold a soft pencil at the correct height, I lightly mark the water line around the hull. At this stage, the hull is still quite fragile; take care when you remove it from the shadows. I start this process by cutting up of the mast and jib booms, and| install the radio board in the hull. By swinging the sail-winch arm through its arc and moving the sheet attachment points back and forth on the booms, I can determine exactly where the sheets should be connected to the booms so that they will exit vertically through the deck. The sheets should not exit at anything less than a right angle (as viewed from the side), or you won’t be able to sheet the sails in hard over the center line. This will affect the boat’s ability ORDER THE FULL-SIZE PLAN. PAGE 73 FSPB 0294 to point high into the wind. $12 ee Before you attach the deck, mark the final positions of the two sheet fairleads the transom and stem pieces loose, then I spread the sheers slightly and ease the light balsa shell up and off the shadows. An alternate method is to cut all of the shadows loose and knock them out of the hull. isn’t a set way to do this. Basically, the on the kingplank. longer the sail-winch arms are, the closer you can move the main- and jib-sheet attachment points to the mast. Conversely, shorter sail-winch arms mean that the boom attachment points Now it’s time to assemble the fin and BELOW THE WATER LINE bulb assembly. A typical U.S. 1-meter lead bulb and fin should weigh 5 pounds At this point, your hull shouldn’t weigh much more than a pound, and the inside will be covered with glue spatters and runs. Before you install the crossmembers and the kingplank, sand these spots with 50-grit sandpaper. A typical U.S. 1-meter kingplank is made of Yex¥2- inch pine or spruce. (Don’t use balsa.) The 4%x’4-inch pine cross-members should be installed on edge. I notch them to set the kingplank flush with them. DOWN THE HATCH You’ll have to experiment to determine the size that the main hatch opening should be. It must be big enough to admit the radio board and your hand and small enough to avoid shipping water when the boat is heeled. Before I determine the hatch size, I build the radio board, which holds the sail winch, the rudder servo, the receiver and the battery pack. I try to make my radio boards compact so that I need only a small access hatch. (See photo.) The radio board can be any shape as long as it’s compact and light. Lite-ply works well, and it can be varnished to a glossy, waterproof finish. FAIRLEADS After the radio board and sail-winch arm have been installed, I position the mainand jib-sheet fairleads. (These are exits in the deck that guide the main and jib sheets to their respective booms.) There Here’s a close-up of the Pop-Up Mfg.* nosnag nylon block that’s used to reduce friction where the sheets exit the deck. Drill a hole in the deck through the pe lank and insert a fairleadseromenet to guide the sheet to the block. In this photo, the Scepter’s hull has been covered with (42-inch aircraft plywood. A paper pattern of the hull outline and the hatch openings was transferred to the ply. Before the deck is attached to the hull, the inside of the deck should be coated several times with thinned epoxy resin. Make sure there are no leaks at the sheers or hatches. have to be moved farther from the mast. You must be able to sheet both the jib and the main booms in hard, so they are over the deck center line when the sailwinch arm is at one end of its travel. At the opposite end of its travel, the main boom should be able to swing out and come in contact against the shrouds, and the jib boom should be perpendicular to the deck center line. SHEET CONTROL Arm travel will vary from winch to winch, You’ll have to experiment to get it right. It’s easier to do this before the deck has been attached. I make a mock- Here’s a radio board. Some skippers prefer a flat board; | make mine out of 342-inch plywood in 2 box form. Use whatever works for you; just keep it pt Note the projecting split tongue that’s plugged into a thin = cross-member that im, has a slot cut in it. Simple! FEBRUARY 1994 29 SCEPTER the hull and the underside of the deck with varnish or thinned epoxy several times. No matter how watertight you think your boat is, I can assure you that it will take on water in a moderate blow. A glossy hull interior will ensure years of pleasant sailing—no matter how many times the model takes on water. Here’s the assembled radio board. Thle receiver on/off switch is mounted on the side for accessibility. (Expose the battery jack, too.) Run the receiver antenna up the mast, or string it out through a plastic tube in the hull. or less. The AMYA class plans provide a full-size bulb pattern and recommend a bulb weight. If you want to go lighter, you can shave the lead down after it has been cast. (A simple plaster mold will do the job, but make sure that the plaster is completely dry when you pour the lead.) This job is better left to those who know how to do it. Cast lead bulbs are available The radio board seen through the hull’s access hatch. It can easily be removed for maintenance. Position the board inside the hull so that none of its components is within allow the bulb to oscillate and slow the boat. The class plans show several methods of constructing the fin and rudder. The rudders are built in the same way as the fins. Use 92-inch brass rod for the rudder post, and run it into the hull through a length of 5/2-inch-i.d. brass tube. An R/C aircraft nose-wheel steer- ing arm provides the link between the rudder servo and the rudder. It’s a good only if you don’t install an access hatch. The fin can be attached to the hull with 6-32 bolts or a tongue-and-box-inthe-hull arrangement. I prefer the tongueand-box method shown in the construc- tion photos. It stiffens the hull and ensures that the fin won’t loosen. Using bolts will leave more room inside the hull, but space really isn’t a problem. ALL HANDS ON DECK For hulls of up to 50 inches long, ¥32- inch aircraft-grade plywood makes a strong, light deck material. In an effort to reduce weight, some skippers use plastic heat-shrink covering material that’s intended for R/C aircraft. This works well and saves weight, but there can be sealing problems at the edges of the deck. I tell beginners to use ¥32-inch plywood or from advertisers in the AMYA “Model Yachting.” newsletter, Fins can be built of ¥2inch plywood or thin Formica® wrapped around an interior structure; or Y16-inch plywood can be sandwiched between hard balsa sheets. Either way, the exterior of the fin should get at least one layer of fiberglass (two would be better). The fin should not flex under the 5-pound bulb when the boat is heeled 40 to 50 degrees in the water. And the fin should not twist and 30 RADIO CONTROL BOAT MODELER hatch openings and the sheet exit posi- Y inch of the bottom. idea to install a small hatch in the deck (above the rudder post). This allows the skipper to tighten the rudder arm if it ever loosens. Think it won’t? Murphy’s Law says it can and will happen—but Here, two U.S. 1-meter boats are ready to sail. The boat on the left is a Squirt that was designed by Bob Jensen. The other is the Scepter by Bob lebow. Both are fast and competitive. I prefer to attach my decks to the hull with slow-setting epoxy, and I use rubber bands and masking tape to hold the assembly in place overnight. A full-size paper pattern of the deck, on which the 342,inch balsa covered with 1.5-ounce fiberglass. If you’re so inclined, you can cover a balsa sub-deck with ¥32-inch mahogany planks, adding ¥32-inch-square brass strips between adjacent mahogany planks. It’s tedious work, but it looks nice. An arced or crowned deck not only looks better, but it also sheds water faster. Before you attach the deck, build the crown into the kingplank and the cross-members, and coat the interior of | tions have been marked, is a useful tool. The plywood can be cut to size before you permanently attach it to the deck. The hatch covers can be as simple or as complicated as you like. There are only two requirements: they must be durable because they will be opened frequently; and they must be watertight. The rudder access hatch will perhaps only be opened once or twice a year. A simple plywood plate and two no. 2 brass round-head screws will do here. Be sure that the main hatch won’t interfere with your mainsail sheet when you remove it. The comer of a raised hatch can snag the main sheet as the sheet is hauled in by the sail winch. MAST Spars (the mast and the booms) can be made of clear white pine, Sitka spruce, extruded aluminum, or carbon fiber. Ski poles make excellent aluminum and fiberglass masts. Sail booms can be made of wood, fiberglass arrow shafts, or stiffened aluminum tube. Whatever you use should be light, stiff and dead-straight. | prefer clear pine or Sitka spruce that’s finished glossy with several coats of clear polyurethane varnish. I wet-sand each coat to a super-glossy finish, letting the natural beauty of the wood come through. This finish will stand up well to several years of sailing with no maintenance. The spreaders can be made of aluminum or brass sheet, or a flattened tube that’s bolted to or run through the mast and secured with CA glue or epoxy. Many freshman skippers assume that the mast should have a groove for the main sail along its rear side. It looks salty, but it’s definitely not the way to go ona model yacht. The mainsail will be far more effective if it’s loosely tied to the mast every 6 inches or so. This allows the sail to set properly and fill on all points of the wind. A bolt-roped sail in a groove is forced to take on an unnatural (Continued on page 50) A ready-to-run, ketch-riggedy ‘motor sailer = {l\ ff) 7, REPORT Out of the box, the Blackstar 35 is a joy. Its generous displacement, full keel and manageable sail area provide predictable handling, which is per- fect fora relaxing day at the lake. Note the extended rudder that counters the turbulence caused hy the fixed prop. Blackstar EWEST Yachts* OFF THE ways at Blackstar R/C is a pretty, ketch-rigged motor sailer—the Blackstar 35. This beamy little yacht, with its twin masts, its inboard electric motor and its scale appearance, is a departure from Blackstar’s usual highperformance fiberglass sailboats, and I was eager to try one out. BUILDER’S CHOICE All Blackstar yachts are available assembled and ready to sail and as kits. The deluxe kits feature basic factory machining and assembly and include appropriate R/C systems. The basic kits don’t include radios and come completely unassembled. by DOUG JACOBS FEBRUARY 1994 35 PHOTOS BY DOUG JACOBS My yacht arrived assembled, witha The Blackstar Motor Yacht kit includes a geared 540 motor, a Hitec electronic speed controller and a NiCd battery pack. SPECIFICATIONS Type: Ketch-rigged motor yacht Length: 35 inches Sail area: 389 square inches (stock); 505 square inches (modified) Weight: 9 pounds Hull material: Fiberglass hull and deck Prop used: Fixed two-blade (stock); folding two-blade (optional) Radio used: Futaba 4BNL 4-channel No. of channels req’d: 3 Power required: Geared 540 List price: $750 (ready to sail) Features: the all-fiberglass Blackstar 35 Motor Yacht comes in kit form with or without an R/C system, or completely assembled and ready to sail. The ready-tosail version is available in several colors, and it includes an inboard electric motor and speed controller for added flexibility and convenience. Comments: out of the box, the Blackstar 35 performs beautifully. Its inboard motor is beneficial for beginning and experienced pilots. Its generous displacement and full keel provide predictable, relaxed handling, and because it’s compact, it can be transported fully rigged in most vehicles. nicely finished yellow hull and matteblack aluminum spars. The nonskid surfaces that had been molded into the fiberglass deck added a nice scale touch. Mylar stick-on film, depicting windows, hatches, etc., provided the only detailing on the deck and the removable fiberglass cabin. No additional detail fittings were included. My boat has a Futaba* 4BNL 4-channel radio to control the sails, the rudder and the inboard electric motor. (The fourth channel isn’t used.) Below deck, a powerful Futaba $125 arm-style sail-winch servo handles the sheeting chores. A Hitec* electronic speed con- interrupt the water flow around the rudder and, thereby, reduce steering efficiency. Graupner’s new – folding, two-blade, straight-edge propeller solves these prob- coat around the holes. Fortunately, there was no structural damage. To beef up the area before proceeding, I added squares of ¥/g-inch plywood underneath the deck for reinforcement. The rigging is simplicity itself! Fore and aft, the wire luff of the jib acts as the main forestay. The main halyard does double duty as a running backstay to the mizzen mast, and the mizzen halyard also serves as a backstay. The luff and the halyards can be adjusted to change the tension. Here’s the completed cabin ready for finishing. After | had added ribs to alter the cabin’s basic shape, | used thin mahogany veneer to sheet On each side, the masts are supported shroud one with that has brass turnbuckles that allow the f the stock fiberg lass assembly. troller with its own Ni-Cd battery pack powers the 540 electric motor. (It’s a motor yacht, remember?) A padded PVC-pipe boat stand, a suit of three Kevlar sails and a tuning manual complete the kit’s inventory. All I had to do was charge the batteries, step the masts and go to the lake! masts to be adjusted easily. Model aircraft-style hinges provide a simple, effective gooseneck for the aluminum booms. My kit didn’t have vangs or outhauls, but you can order them. (Vangs prevent boom lift on some points of the sail; outhauls adjust the draft of the sails to suit wind conditions.) The main mast On the water, the and the mizzen mast Blackstar 35 is a are stepped directly onto the deck; their mroatridin joy! Its generous displacement and brass- prouuains tube “stubs” are keyed into predrilled locater holes on the deck’s sur- face. Trialfitting the ~ > TM full keel provide predictable angles oof heel without m being too “tippy,” ; add interest to wieoden raillings and hatches and the split rig and secure the rails to the hull. provide good accel- masts and the stand. ~~—és hte: fiberglass deck. Notice the pins that Graupner’s Folding Prop dding an electric motor and propeller to a sailboat has always been a giveand-take situation. Being able to motor about when the wind isn’t doing its thing is paid for in the drag the propeller creates when it’s not in use. Also, depending on its position, the prop can create turbulence and | a spider web of stress cracks in the gel- lems. When the motor turns the prop shaft, the prop opens because of centrifugal force: and when the prop isn’t in use, water drag folds the blades back. What makes this propeller unusual are the cogs that connect the blades at the hub. Both blades are extended or folded simultaneously and at the moderate sail plan same rate, so the prop is always balanced. Made of reinforced plastic, the blades and the hub are very strong. The prop hub comes with a threaded insert that’s available in all common shaft _ sizes. You’ll be impressed by the quality and precision of this unit. By combining the utility of propeller drive and the efficiency of sail power, this new folding prop will greatly increase your modeling fun without sacrificing your model’s performance. aluminum. I shaped the tow rails and handrails out of spruce strips from my scrap box. After I had applied stain and varnish, I used brass rod to pin the railings into place. The stock fiberglass cabin is flaton top and too blunt (it’s rectangular with slanted sides) to blend with the ee To complement the hull treatment molded in at the factory, | added a nonskid surface to the raised deck. For contrast, | painted all these surfaces light blue. eration, if not blinding speed. The Blackstar 35 ketch is just like its bigger brothers: it’s happiest sailing on a reach, where all its sails can work efficiently without getting in one another’s way. Used with a Graupner* folding propeller, the auxiliary electric motor is gréat fun because it allows your boat to scurry to safety, motor leisurely to the next patch traditional look I was after. I added a straight rib to the center of the cabin top and an angled rib to its front. Then | skinned the ribs and fiberglass cabin surfaces with mahogany veneer so This close-up of the rear deck shows some of the detailing | I replaced the Mylar trim film with brass portholes and installed a few mis- cellaneous fittings from my scrap box. I treated the hull wind, or simply befuddle becalmed to a white epoxy buddies! paint job, painted marine-blue epoxy onto the bottom, PASS THE SALT The Blackstar 35 and used red chart features sanitary tape for a water line. On the deck, | decks and black- For a more scale appearance, | added boom vangs, cleats and winches to the main mast and the mizzen mast. These fittings greatly improve the model’s functioning and help it take full advantage of my new sails. “saltier,” more_traditional appearance, however, so I decided to customize my yacht. The stern and the bow pulpits are the most notable additions I made to the Blackstar. I fashioned them out of brass rod and painted them with chrome auto- motive spray paint to simulate polished contributor and sail guru Rod Carr stitched up a gorgeous new suit of Dacron sails. They take full advantage of the that the front is a shallow added. | supplied the Mylar taller masts and create a sticker “windows” with brass vee and the top is slightly portholes. more powerful rig. (I crowned. This is much betd Dacron to specifie and hatches ter! Mahogany retain the “character” of the vessel; seerailings add the finishing touches. of out accents in the best “eco-yacht” tradition, and its sea-kindly hull form and split sail rig just ooze character. I prefer a of my calculator, I found that most rigs | that looked “right” to me had a main mast whose height was approximately | 116 percent of the overall boat length and a mizzen mast whose height was | approximately 67 percent of the height of the main mast. Using these formulas, I made taller masts that allowed me to significantly increase the total sail area. Fellow Radio Control Boat Modeler used harbor-blue enamel to highlight the beautiful nonskid pattern, and | added a similar nonskid coating to the raised deck. My yacht looked so good that I decided to add more horsepower with a new suit of sails. SUITABLE SAILS Sea trials confirmed the boat’s ability to carry more sail, so I hit the books in search of new sail plans. With the help through sails ain’t scale!) As a final touch, I had Rod make my mizzen sail light blue to complement the harborblue finish on the deck. I replaced all the deck hardware with pe-ka-be fittings. They’re distributed by R/C Model Yachts and Accessories”, whose catalogue includes jewel-like turnbuckles, blocks, cleats and other goodies crafted of machined stainless steel and nylon. I selected their quick-release, “micro-adjustable” turnbuckles to tension the shrouds, and I use their double turnbuckles as boom vangs and to ten- sion the backstay. I also replaced the factory-supplied hinge points with brass goosenecks from A.J. Fisher. Back on the water, the transformation was amazing; I had expected performance to improve and | wasn’t disappointed. The little yacht came alive as the higher aspect ratio and generous draft of my new sails let the breeze do its job better by allowing the “sweet spot” to be raised. The increased sail area provides acci- tional acceleration and snap, and the handling remains predictad.e. yet responsive. CONCLUSIONS It should be noted that, althowgnh this project goes beyond the soc ditional kit review. my ¢ explore the potential of my yecht wes made with the bi e Yachts. Some of t were for personal or cosmetic reasoms For a scale look, | added a bow pulpit and a stern pulpit made of brass rod. Tiiking of R/C in your Midwest Model Boat Kit? Check out M.A.C.K. for Power and Running Hardware. You’ll get twice the power and over twice the run time at half the cost. SCEPTER (Continued from page 30) flat spot in its center. It’s also much easier to run a jack line up the rear of the mast than it is to rout out that tiny bolt-rope groove. SAILS The AMYA lists several sail makers who will provide custom suits of sails for your U.S. 1-meter for less than $100, or you can make your own. I’ve found that whether you purchase or make your sails doesn’t make much difference in the club standings. Most of the skippers in our club make their own sails out of various weights of commercial spinnaker cloth, rip-stop nylon, Dacron, or even 2-mil clear Mylar. Some skippers broad-seam their sails to add fullness, some cut their Come to M.A.C.K., “The Model Motor People,” Leaders in Model Marine Performance Systems. suits from a single piece of material and others make multi-panel sails. Over the last six years, we’ve found that the cut of the sails (flat or broadseamed) is only a small part of consistent- For further information send $4 for complete catalog to: M.A.C.K. Products Model Marine P.O. Box 464 Long Branch, N.J. 07740 (908) 870-2966 ly winning races. Custom sails look great, DEALER but if the skipper isn’t on a par with the INQUIRIES INVITED! VISA & MASTERCARD ACCEPTED ($50.00 MINIMUM PURCHASE) rest of the fleet, custom-made sails aren’t going to help him very much. I’ve seen skillfully piloted boats with flat sails outrun boats with custom sails. It’s better to start with flat sails; you can try broad-seaming later, following AMYA instructions. One of the best materials for sheets is 30-pound-test, braided, fly-fishing line. You can cut the shrouds and stays out of 28 YEAR TRACK RECORD stainless-steel wire or plastic-coated fishing leader. I’ve used plastic-coated leader for years, and I’ve never had a problem. Put short pieces of crimped brass tube on the ends of the shrouds and the stays. The Parts People of DEALER INQUIRIES INVITED PH: 1-504-242-5967 FAX: 1-504-244-1200 VISA / MASTERCARD ACCEPTED Steel, 2-56, R/C aircraft clevises work well as ends for the shrouds and the C ion 7 , Une. P.O. BOX 26247 » NEW ORLEANS, LA 70186 stays and as points where they can be attached to the deck. They also allow the easy removal of the sail rig (if this ever becomes necessary). BOAT MODELERS es Looking For… * Hard-to-Find Fittings? +» Improved Performance? * Longer Running Time? + How to Refurbish or Repair? , ° Off-the-Shelf or Customized Powerplants? ; f * R/C & Static Kits Matched to Your Skill Level? iM Sh ips N’ Thi ngs Truly Knowledgeable Service P.O. Box 605-B Somerville, NU 08876 (908) 722-0075 FITTINGS Cut a 4-inch-wide brass strip into 34-inch lengths, and bend them to the desired angles to provide nearly all of your boat’s deck fittings—including the chain plates, the backstay fitting and the jib rack. In one end of each strip, drill a .060-inch hole to accept a clevis pin. Two more — CATALOG $5 — REFUNDABLE WITH FIRST $25 ORDER 24-HOUR FAX ORDERING (908) 725-8397 holes to fit no. 2 brass screws will secure the fittings to the deck. Before you bolt the fittings to the deck with 2x’/2-inch brass round-head screws, drill small starter holes in the deck. Be sure that there are blocks inside the hull to hold these screws. (Continued on page 53) 50 RADIO CONTROL BOAT MODELER SCEPTER (Continued from page 50) PERFORMANCE So, how does the Scepter sail? In two TEKIN words: very well. It’s a rocket going down- HIGH PERFORMANCE R/C ELECTRONICS track. My boat is as competitive as any I’ve built. It has taken second place in our club’s standings for the past two years; if I improve my thumbs, maybe I’ll get a firstplace win soon. RECORD TSC 432M MARINE SPEED CONTROL Powerful 300 amp high frequency drive AM & FM MICRO RECEIVERS Small and light, to make your boat jump. wind, and it sails windward as if it’s on a NANMBA powers most boat motors up to 32 cells. *Here are the addresses that are pertinent to this article: AMYA,; send an SASE to membership secretary Patricia Hein, 1884 Campus Ct., Rochester Hills, MI 48309. Hobbypoxy Products, Div. of Pettit Paint Co. Inc., 36 Pine St., Rockaway, NJ 07866. Victor Engineering, 1000 Calle Cordillera, San Clemente, CA 92673. AMYA U.S. 1-Meter Class rules and plans catalogue, send $1 and an SASE to Steve Andre, 600 Sheffield Ct., Chula Vista, CA 91910. Pop Up Mfg. Co., 27 Emerson Ave., Amityville, NY 11701. Futaba Corp. of America, 4 Studebaker, Irvine, CA 92718. L PEAK CHARGERS Dependable, automatic, and easy to use, they deliver along YOUR ator ~spE HEALER SeataloS high perform- ance charge. TEKIN ELECTRONICS, INC. 940 Calle Negocio, San Clemente, CA 92673 (714)498-9518 FAX (714) 498-6339 MADE IN U.S.A. BLACKSTAR BOATECH ENGINEERING INC. (Continued from page 37) only, but others had a definite impact on performance. Because of the success I had with my prototype, the manufacturer will incorporate the taller rig, the folding propeller, the increased sail adjustability and some of my cosmetic touches in future Blackstar 35s. Heartfelt thanks to Rod Carr, who designed and cut the sails; Herb Hoefer of R/C Model Yachts and THESE RACE PROVEN HULLS REPRESENT THE ULTIMATE IN AERODYNAMICS AND HYDRODYNAMICS, MAKING OUR BOATS SOME OF THE FASTEST, MOST STABLE ON THE MARKET TODAY. * FACTORY JOINED* *HAND LAYED FIBERGLASS* *LusTRous Get COAT FiNISH* Accessories, who imports and distrib- *Rapio Box AND SNAP-ON COWLIN G INCLUDED* utes the superb pe-ka-be line of model yacht hardware; and Chris Lones of Blackstar Yachts, who endured my FROM A BARE HULL TO RACE READY, OR ANYTHING IN middle-of-the-night phone calls (time BETWEEN — THE CHOICE difference?—what time difference?) Is yours! and patiently listened to my questions and requests. Blackstar Yachts should be proud of their newest release; for a ready-tofloat package of looks, quality and per(Continued on page 59) Dealer 1-800-MEANCAT Box (305) 63-4757 Florida 32063 749-6413 BOAT FUEL Add $5 UPS Hazardous Oil Blend 80% Synthetic / 20% Castor Shipping Fee N.C. residents add 6% sales tax Nitro ORDERS: P.O. Margate, Inquiries Invited 25% 1 Gal. 18.00 35% 21.00 45% 24.00 50% 26.00 60% 28.50 | ——. TRINITY MANUFACTURING INC., P.O. BOX 1519, 11 E.V. HOGAN DRIVE, HAMLET, N.C. 28345 BLACKSTAR FUN CRUISER formance, the Blackstar Motor Yacht is no. 7140 After Run Oil and Cable Grease, a T-25 Torx wrench (for the engine screws) and a 5/64 hex wrench (Continued from page 57) (Continued from page 53) tough to beat. *Here are the addresses of the companies mentioned in this article: GREAT PLANES Kyosho arine Motors If you want adjustable timing and you like endbell watercooling units, try one of these new Kyosho motors. They’re compatible with directdrive water pick-ups and standard hull pick-ups, and they come with adapter hardware for water pick-ups and water outlets. For gear-reduction applications, try the high-speed Super Marine Type G motor; for direct-drive models, try the high-torque Super Marine Type D motor— ideal for small, fast, high-performance boats. Price—$124.99: part nos.—KYOG2500 (REV Super Marine Type D); KYOG2501 (REV Super Marine Type G). Great Planes Model Distributors, P.O. Box 9021, Champaign, IL 61826; (217) 3986300. DREMEL for the ferrule and drive dog. At $49.95, the Spare Parts Kit is good value. If you have these parts on hand, you’ll be able to make repairs on the spot without having to visit the hobby shop or wait for a delivery from your favorite mail-order supplier. Prather also offers a high-performance, large-bore carburetor (no. 9300), which is Blackstar R/C Yachts, 10531 S.W. 207th St., Miami, FL 33189. Futaba Co -on America, 4 Studebaker, Irvine, CA 9271 Hitec/RCD, 16729 Wheatlands Ave., Ste. C, Santee, CA 92071. Graupner; distributed by Hobby Lobby Intl., 5614 Franklin Pike Cir., Brentwood, TN 37027. R/C Model Yachts and Accessories, 675 S.W. 238th Ave., Hillsboro, OR 97123. Lb said to increase the Cruiser’s overall speed by 3 to S5mph. NITRO NEWS Although I tested this boat on smooth water, like all deep-vee models, it will easily handle rough water. Prather offers a video in which you can watch the Fun Cruiser on the Colorado River, and the action is non-stop. The film was taken from a powerboat and shows the Cruiser jumping waves and negotiating the wakes of passing boats—a very impressive (Continued from page 47) ered by an OPS 90 engine, Joe Pagani Sr. showed everyone the fast way around the irregular offshore course by setting a NAMBA record in the X Offshore event. Racing in Pennsylvania was a lot of fun, and I made several new friends. As I look back on the “93 NAMBA Nats, | certainly look forward to returning and to racing with all those fast deep-vee and offshore boats. If you live near the East Coast and you aren’t affiliated with local clubs and races, you’re missing out on a lot of fun. Join up with the good people in organized R/C boating. performance. If you’re considering model boating as a hobby, ease of use, parts availability and cost of operation should be primary considerations. Prather Product’s Fun Cruiser will definitely put the “fun” into your model boating experience. *Here are the addresses of the companies mentioned in this article: Prather Products Inc., 1660 Ravenna Ave., Wilmington, CA 90744. *Here are the addresses that are pertinent to this article: Paasche Airbrushes, 7440 W. Lawrence Ave., Harwood Heights, IL 60656. Twin Craft, 48 i enanae Elizabethtown, PA 17022. Airtronics Inc., 11 Autry, Irvine, CA 92718. WenaProducts, 480 Bonner Rd., esi N. Rd., Aeromarine Laminates, 78 E. Industry Ct., Deer Park, NY 11729. OPS Motors; distributed by Shamrock Competition ser P.O. Box 26247, New Orleans, LA 701 Picco Engines; distributed by Tidewater Engineering, 2406 W. Madison Ave., P.O. Box 1135, Bastrop, LA 71220. O.S./Great Planes Model Distributors, P. E Box 9021, Champaign, IL 61826 Variable-Speed Scroll Saw Precisely cut smooth curves in wood, metal and plastic with this 16-inch Scroll Saw, which cuts at 200 to 2,000 strokes per minute. Check the LED digital readout to find the optimal cutting speed for the thickness and type of material you want to cut. A built-in sawdust blower keeps the cutting line clear, and the clear-plastic blade guide pivots out of the way when you want to change the blade. The saw’s smooth, 12-inch-diameter, cast aluminum table tilts up to 45 degrees, and a degree scale ensures the accuracy of bevel cuts. Thirteen assorted 5-inch blades are included. Price—$398 Dremel, Dept. RF, 4915 21st St., Racine, WI 53406; (800) 437-3635, ext. 2. BLACKSTAR R/C YACHT * All FIBERGLASS CONSTRUCTION * * KBVLAR SAILS HIGH PBRFORMANCE SAILING ACTION BLACKSTAR sailboats are designed to snail, not junt sit on a sholf. From our 27″ to our 70” you get high performance sailing action and quality that will last for years. We also offer hardware, custom sail making, masts, rigging, and rudders For a for FREE envelope to: (305)235-9912 any boat. Keels brochure, send a stamped self addressed business Blackstar R/C Yacht 10531 SW 207 ST Miami FL 33189 BLACKSTAR 27 BLACKSTAR 37 RTS $ 295.00 Kit $ 245.00 RTS $ 395.00 Kit $ 345.00 BLACKSTAR 37 America’s Cup 92 RTS $ BLACKSTAR 40 Ketch RTS $ 495.00 Kit $ 445.00 750.00 Kit $ 675.00 NEW FOR 93 900.00 Kit $ 800.00 NEW FOR 93 RTS $ 795.00 Kit $ 700.00 NEW FOR 93 BLACKSTAR 78 America’s Cup 92 RTS $1200.00 Kit $ 999.00 BLACKSTAR 40 Motor Yacht BLACKSTAR 50 H-Class RTS $ RTS= Ready to sail, all prices include radio and sail control. Shipping and Handling not included.





