E L E M T B Tone your= RADIO CONTROL ips or thenon get into t i ow! – ‘ Don’t Melt Down! A Speed Controller that can Handle the Heat Learn from a Pro —Acdvice for ~ oa Beginners € \ #97 OW5 AVN 69° 20 LOW ba m a) Se LT9 LIOLO-f:e6eeeeeddNaNnx at vs HOW To: e Ultimate:Mono = the Perfect Field Box Build Sailboat Fittings@em Recor 2 saat eit | hie USA $3.50 CANADA $3.95 | HOBBY LOBBY KEY BISCAYNE KYosHo NITRO VIPER -miéidsiicns Hirec SEA NYMPH maus motorsports CHAMP .45 TUNNEL 11 ___ go” Be fit” oHOW 0 ‘Tro ? eal a vw? BUILDING THE Robinson 27 ailboat PART 3 Painting and deck-fitting techniques from the master by ROD CARR from the mainsheet, which ends at the build an inexpensive, but competitive, matching 1/s-inch-wide strips of ¥2-inch-thick magnetic sign material, with the white vinyl peeled off, make an R/C yacht. Part 1 (November ’92) dealt excellent hatch seal. Stick the strips to ¥g-inch plywood that has been partially N THIS SERIES, I describe the materials and techniques used to scratch- with the construction of the hull out of foam, fabric and resin. Part 2 (April 93) showed the techniques used to complete the hull, attach the deck, set the fin and construct the bulb (hull plans were also published). This month, I describe hatch construction, painting the hull, R/C gear installation and selected deck fit- tings. In future issues, I’ll discuss sail- rigging options and show you how to THE HATCH There are many clever ways to seal the hatch. Although they’re a little heavy, ¥ hardened with thin CA Figure 1 reinforcement L —= iM a VI in. | 14, 3/s-inch no. 1 wood screws. Be careful not to strip : out the threads that form in the deck, and strengthen each thread exact position and, under normal condi- a few moments to secure, it’s 100 per- tions, will be completely waterproof. cent waterproof and strong enough to with thin CA. Although this hatch takes I took a different route, desiring take the main sheet attachment. To to save as much complete the woodwork on the deck, weight as possible install a small mast step as shown on the (see construction diagram (to be published in Figure 1). ie construction methods Part 4). fingers are fat, a PAINTING rather large hatch To produce an even, matte finish, sand the entire hull, deck, fin and bulb with 220-grit wet-and-dry sandpaper. (Also do all this on a piece of scrap plywood that you’ll use later for compatibility test- where the mainsail CONTROL BOAT MODELER 6 in. stripes of double-stick tape. A hatch made using this method will fall into the part of the boat RADIO The hatch is screwed down right through the tape with a eel was required. The hatch has to cover 50 opening. YisxY4-in. foam tape ‘ud Y%-in. ply. 1/6xY4-inch foam seating around the edge of the hatch /-in. plywood hatch cover Threaded hoe its thickness and weight; tape is applied to the deck ¥g-in. no. 1 flat-head wood screws quite small and my emphasize simplicity and strength. | HATCH CONSTRUCTION DETAIL Because this boat is The Robinson 27’s deck-fitting arrangement. The The hatch cover itself is made of the hatch and deck with ¥/s-inch-wide | routed out on the underside to reduce produce a set of serviceable sails at a reasonable cost. hatch cover’s center line. is sheeted. A bridle ing.) Spray on two or three light, mist could be used, but | chose to have the coats of black primer. When that’s dry, spray on four or five mist coats of white primer. When the white has dried, wet- hatch take the load , MODIFIED FUTABA S125 SERVO ARM Figure 2A sand with 600-grit wet-and-dry paper —<—_ %in. and plenty of soapy water. The soap is required to prevent the paper from “loading up.” al sheet ~> JIB TRAVELER SLIDER ; Figure 6 ~





